Table of Contents
Advertisement
76: Reverb BrightRoom
This room-type reverb emphasizes the early reflections that
make the sound brighter.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Left
EQ Trim
LEQ
HEQ
+
Pre Delay
EQ Trim
Right
Reverb Time
0.1...3.0
[sec]
a
High Damp [%] 0...100
Pre Delay
0...200
[msec]
b
Pre Delay Thru
0...100
[%]
c
ER Level
0...100
d Reverb Level
0...100
e
EQ Trim
0...100
Low,
Pre LEQ Fc
Mid-Low
f
High,
Pre HEQ Fc
Mid-High
Pre LEQ Gain
–15.0...+15.0
[dB]
g
Pre HEQ Gain
–15.0...+15.0
[dB]
Dry, 1:99...99:1,
Wet/Dry
Wet
h
Src
Off...Tempo
Amt
–100...+100
c: ER Level
d: Reverb Level
These parameters set the early reflection level and reverb level.
Changing these parameter values allows you to simulate the type
of walls in the room. That is, a larger "ER Level" simulates a hard
wall, and a larger "Reverb Level" simulates a soft wall.
Level
Dry
ER
(Early Reflections)
Pre Delay Thru
Pre Delay
77: Early Reflections
This effect is only the early reflection part of a reverberation
sound, and adds presence to the sound. You can select one of the
four decay curves.
FX Amt
ER Level
ERs
Pre Delay Thru
Reverb
Reverb Level
ERs
ER Level
FX Amt
Sets the reverberation time
Sets the damping amount in the
high range
Sets the delay time from the dry
sound
Sets the mix ratio of non-delay
sound
Sets the level of early reflections
Sets the reverberation level
Sets the EQ input level
Selects the cutoff frequency (low or
mid-low) of the low-range equalizer
Selects the cutoff frequency (high or
mid-high) of the high-range
equalizer
Sets the gain of Low EQ
Sets the gain of High EQ
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 243
Amount of modulation source
Reverb - Room Type
Reverb
Time
Reverb Time
Reverb and Early Reflections (Reverb ER)
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Left
EQ Trim
LEQ
HEQ
+
Pre Delay
EQ Trim
Right
Sharp, Loose,
a
Type
Modulated,
Reverse
b ER Time [msec] 10...800
Pre Delay
c
0...200
[msec]
d EQ Trim
0...100
Low,
Pre LEQ Fc
Mid-Low
e
High,
Pre HEQ Fc
Mid-High
Pre LEQ Gain
–15.0...+15.0
[dB]
f
Pre HEQ Gain
–15.0...+15.0
[dB]
Dry, 1:99...99:1,
Wet/Dry
Wet
g
Src
Off...Tempo
Amt
–100...+100
a: Type
This parameter selects the decay curve for the early reflection.
Sharp
Loose
Modulated
Reverse
Dry
Pre Delay
Effects
287
FX Amt
Early Reflections
FX Amt
Selects the decay curve for the early
reflection
Sets the time length of early
reflection
Sets the time taken from the original
sound to the first early reflection
Sets the input level of EQ applied to
the effect sound
Selects the cutoff frequency (low or
mid-low) of the low-range equalizer
Selects the cutoff frequency (high or
mid-high) of the high-range
equalizer
Gain of the Low EQ
Gain of the High EQ
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 243
Amount of modulation source
Early Reflections - Type
ER Time
Advertisement
Table of Contents
