Korg PA600 Reference Manual page 315

Proffesional arranger
Hide thumbs Also See for PA600:
Table of Contents

Advertisement

121: St/Cross Long Delay
(Stereo/Cross Long Delay)
This is a stereo delay, and can by used as a cross-feedback delay
effect in which the delay sounds cross over between left and
right by changing the feedback routing. You can set a maximum
of 2,730msec for the delay time.
Stereo In - Stereo Out
Left
High Damp Low Damp
Delay
Input Level D-mod
Stereo/Cross
Feedback
High Damp Low Damp
Input Level D-mod
Delay
Right
a
Stereo/Cross
Stereo, Cross
b L Delay Time
0.0...2730.0
[msec]
R Delay Time
c
0.0...2730.0
[msec]
L Feedback
–100...+100
d
Src
Off...Tempo
Amt
–100...+100
R Feedback
–100...+100
e
Amt
–100...+100
f
High Damp [%] 0...100
g Low Damp [%] 0...100
Input Level
–100...+100
Dmod [%]
h
Src
Off...Tempo
i
Spread
–50...+50
Dry, 1:99...99:1,
Wet/Dry
Wet
j
Src
Off...Tempo
Amt
–100...+100
FX Amt
Stereo/Cross
Spread
FX Amt
Switches between stereo delay and
cross-feedback delay
Sets the delay time for the left
channel
Sets the delay time for the right
channel
Sets the feedback amount for the
left channel
Selects the modulation source of
feedback amount
Sets the modulation amount of the
left channel feedback
Sets the feedback amount for the
right channel
Sets the modulation amount of the
right channel feedback
Sets the damping amount in the
high range
Sets the damping amount in the low
range
Sets the modulation amount of the
input level
Selects the modulation source for
the input level
Sets the width of the stereo image of
the effect sound
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 243
Amount of modulation source
122: Hold Delay
This effect records the input signal and plays it back repeatedly.
You can control the start of recording and reset via a modulation
source. Easy to use for real-time performances.
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Left
+
Delay
Loop Time: Auto/ ...5400ms
Right
D
-mod
REC Control
D
-mod
RST Control
Loop Time
a
Auto, 1...10800
[msec]
Loop BPM
b
Off, On
Sync
MIDI,
BPM
40.00...
300.00
c
Time Over?
---, OVER!
Loop Base
r...w
Note
d
Times
x1...x32
REC Control
e
Off...Tempo
Src
f
RST Control Src Off...Tempo
g Manual REC
REC Off,
Control
REC On
Manual RST
h
Off, RESET
Control
L100...L1, C,
Pan
R1...R100
i
Src
Off...Tempo
Amt
–100...+100
Dry, 1:99...99:1,
Wet/Dry
Wet
j
Src
Off...Tempo
Amt
–100...+100
a: Loop Time [msec]
With Auto, the loop time is automatically set. Otherwise, you
can specify the loop time.
When Auto is selected, the Loop Time is automatically set to the
time it takes for a performance recorded while the Modulation
Source or "Manual REC Control" is on. However, if the time
length exceeds 10,800msec, the loop time will be automatically
set to 10,800msec.
c: Time Over?
You can set the delay time up to 10,800msec. If the delay time
exceeds this limit, the error message "OVER!" appears in the dis-
play. Set the delay time parameters so that this message will not
appear. "Time Over?" is only a display parameter.
b: Loop BPM Sync
c: BPM
d: Loop Base Note
d: Times
If "Loop BPM Sync" is on, the "Times" setting is ignored; the
loop time is determined by "BPM, " "Loop Base Note, " and
Effects
311
Double Size
FX Amt
Pan
FX Amt
Tempo
BPM
Base Note x Times
BPM
Sets Automatic loop time setup
mode or specifies loop time
Specifies whether delay time is set
in milliseconds, or as a note value
relative to tempo
MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
An error indication that appears if
delay time exceeds the upper limit
when MIDI/Tempo Sync=On
Selects the type of notes to specify
the delay time
Sets the number of notes to specify
the delay time
Selects control source for recording
Selects control source for reset
Sets the recording switch
Sets the reset switch
Sets the stereo image of the effect
Selects the modulation source of
stereo image of the effect
Sets the modulation amount of
stereo image of the effect
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 243
Amount of modulation source

Advertisement

Table of Contents
loading

This manual is also suitable for:

Pa600q

Table of Contents