Table of Contents
Advertisement
50: Detune
Using this effect, you can obtain a detune effect that offsets the
pitch of the effect sound slightly from the pitch of the input sig-
nal. Compared to the chorus effect, a more natural sound thick-
ness will be created.
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
Left
Input Level
+
Detune
Input Level
Right
Pitch Shift
–100...+100
[cents]
a
Src
Off...Tempo
Amt
–100...+100
Delay Time
b
0...1000
[msec]
Feedback
–100...+100
c
High Damp [%] 0...100
Input Level
–100...+100
Dmod [%]
d
Src
Off...Tempo
Dry, 1:99...99:1,
Wet/Dry
Wet
e
Src
Off...Tempo
Amt
–100...+100
d: Input Level Dmod [%]
d: Src
This parameter sets the dynamic modulation of the input level.
Input Level
x1.0
Input Level Dmod= +50
x0.5
Input Level Dmod= +100
D
-mod
Higher
Zero
Max
FX Amt
High Damp
Delay
Feedback
FX Amt
Sets the pitch difference from the
input signal
Selects a modulation source for
pitch shift
Sets the modulation amount for
pitch shift
Sets the delay time
Sets the feedback amount
Sets the damping amount in the
high range
Sets the modulation amount of the
input level
Selects the modulation source for
the input level
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 243
Amount of modulation source
Input Level Dmod
Input Level
x1.0
Input Level Dmod= –50
Input Level Dmod= –100
x0.5
D
-mod
Higher
Zero
Max
Modulation and Pitch Shift (Mod./P.Shift)
51: Pitch Shifter
This effect changes the pitch of the input signal. You can select
from three types: Fast (quick response), Medium, and Slow (pre-
serves tonal quality). You can also create an effect in which the
pitch is gradually raised (or dropped) using the delay with feed-
back.
FX Amt = 100: Mono In - Mono Out / FX Amt = 0: Stereo In - Stereo Out
Left
Input Level
+
Pitch Shifter
Pre
Feedback Position
Input Level
Right
Slow, Medium,
a
Mode
Fast
Pitch Shift [1/
–24...+24
2tone]
b
Src
Off...Tempo
Amt
–24...+24
Fine [cents]
–100...+100
c
Amt
–100...+100
Delay Time
d
0...2000
[msec]
Feedback
e
Pre, Post
Position
Feedback
–100...+100
f
High Damp [%] 0...100
Input Level
–100...+100
Dmod [%]
g
Src
Off...Tempo
Dry, 1:99...99:1,
Wet/Dry
Wet
h
Src
Off...Tempo
Amt
–100...+100
a: Mode
This parameter switches the pitch shifter operating mode. With
Slow, tonal quality will not be changed too much. With Fast, the
effect becomes a Pitch Shifter that has a quick response, but may
change the tone. Medium is in-between these two. If you do not
need to set too much pitch shift amount, set this parameter to
Slow. If you wish to change the pitch significantly, use Fast.
b: Pitch Shift [1/2tone]
b: Src
b: Amt
c: Fine [cents]
c: Amt
The amount of pitch shift will use the value of the Pitch Shift
plus the Fine value. The amount of modulation will use the b:
Amt value plus the c: Amt.
The same Modulation Source is used for both Pitch Shift and
Fine.
e: Feedback Position
f: Feedback
When Feedback Position is set to Pre, the pitch shifter output is
again input to the pitch shifter. Therefore, if you specify a higher
Effects
273
FX Amt
High Damp
Delay
Post
Feedback
FX Amt
Switches Pitch Shifter mode
Sets the pitch shift amount by steps
of a semitone
Selects the modulation source of
pitch shift amount
Sets the modulation amount of
pitch shift amount
Sets the pitch shift amount by steps
of a cent
Sets the modulation amount of
pitch shift amount
Sets the delay time
Switches the feedback connection
Sets the feedback amount
Sets the damping amount in the
high range
Sets the modulation amount of the
input level
Selects the modulation source for
the input level
Balance between the wet and dry
signal
Table , "Dynamic Modulation
sources, " on page 243
Amount of modulation source
Advertisement
Table of Contents
