Yamaha O1V96 Owner's Manual page 269

FREEZE
One input, one output basic sampler (Available for
internal effects 1 and 2.).
Parameter Range
In MANUAL mode, recording is
started by pressing the REC and
PLAY buttons. In INPUT mode,
REC MODE MANUAL, INPUT Record-Ready mode is engaged
by pressing the REC button, and
actual recording is triggered by
the input signal.
Recording delay. For plus values,
recording starts after the trigger
–1000 to +1000
REC DLY is received. For minus values,
ms
recording starts before the trig-
ger is received.
Input trigger level (i.e., the sig-
TRG LVL –60 to 0 dB nal level required to trigger
recording or playback)
Once playback has been trig-
gered, subsequent triggers are
TRG MASK 0–1000 ms
ignored for the duration of the
TRG MASK time.
In MOMENT mode, the sample
plays only while the that the
PLAY button is pressed. In CONT
mode, playback continues once
MOMENT, the PLAY button has been
PLY MODE
CONTI., INPUT pressed. The number of times
the sample plays is set using the
LOOP NUM parameter. In INPUT
mode, playback is triggered by
the input signal.
Playback start point in millisec-
1
START
onds
Playback end point in millisec-
END 1
onds
LOOP Loop start point in milliseconds
1
LOOP Number of times the sample
0–100
NUM plays
START
2
Playback start point in samples
[SAMPLE]
END
Playback end point in samples
2
[SAMPLE]
LOOP
Loop start point in samples
2
[SAMPLE]
–12 to +12 semi-
PITCH Playback pitch shift
tones
FINE –50 to +50 cents Playback pitch shift fine
PLAY button can be triggered by
MIDI TRG OFF, C1–C6, ALL using MIDI Note on/off mes-
sages.
1. 0.0~2970.5 ms (fs=44.1 kHz), 0.0~2729.2 ms (fs=48 kHz),
0.0~2970.5 ms (fs=88.2 kHz), 0.0~2729.2 ms (fs=96 kHz)
2. 0~131000 (fs=44.1 kHz, 48 kHz), 0~262000 (fs=88.2 kHz,
96 kHz)
ST REVERB
Two input, two output stereo reverb.
Parameter Range
REV TIME 0.3–99.0 s Reverb time
Hall, Room, Stage,
REV TYPE Reverb type
Plate
INI. DLY 0.0–100.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
LO. RATIO 0.1–2.4 Low-frequency reverb time ratio
Reverb diffusion (left–right
DIFF. 0–10
reverb spread)
DENSITY 0–100% Reverb density
Balance of early reflections and
E/R BAL. 0–100% reverb (0% = all reverb, 100% =
all early reflections)
Parameter
HPF
LPF
Description
M.BAND DYNA.
Two input, two output 3-band dynamics processor,
with individual solo and gain reduction metering for
each band.
Parameter
LOW GAIN –96.0 to +12.0 dB
MID GAIN
HI. GAIN
PRESENCE
CMP. THRE 24.0 to 0.0 dB
CMP. RAT
CMP. ATK
CMP. REL
CMP. KNEE 0–5
LOOKUP
CMP. BYP
L–M XOVR
M–H XOVR 21.2 Hz–8.00 kHz
SLOPE
CEILING
EXP. THRE
EXP. RAT
EXP. REL
EXP. BYP
LIM. THRE
LIM. ATK
LIM. REL
LIM. BYP
LIM. KNEE
SOLO LOW OFF, ON
SOLO MID
SOLO
HIGH
1.
Other preset effects (COMP276, COMP276S,
COMP260, COMP260S, EQUALIZER601, OPEN-
Description
DECK, REV-X HALL, REV-X ROOM, REV-X
PLATE) are optional Add-On Effects. For more
information on these effects, refer to the Owner's
Manual that came with the Add-On Effects pack-
ages.
Effects Parameters
Range
THRU,
High-pass filter cutoff frequency
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
Low-pass filter cutoff frequency
THRU
Range
Low band level
–96.0 to +12.0 dB Mid band level
–96.0 to +12.0 dB High band level
For positive values, the threshold
of the high band is lowered and
the threshold of the low band is
–10 to +10 increased. For negative values,
the opposite will occur. When
set to 0, all three bands are
affected the same.
Compressor threshold
1:1 to 20:1 Compressor ratio
0–120 ms Compressor attack
1 Compressor release time
Compressor knee
0.0–100.0 ms Lookup delay
OFF, ON Compressor bypass
21.2 Hz–8.00 kHz Low/mid crossover frequency
Mid/high crossover frequency
–6 to –12 dB Filter slope
–6.0 to 0.0 dB, Specifies the maximum output
OFF level
–54.0 to –24.0 dB Expander threshold
1:1 to ∞:1
Expander ratio
1
Expander release time
OFF, ON Expander bypass
–12.0 to 0.0 dB Limiter threshold
0–120 ms Limiter attack
Limiter release time
1
OFF, ON Limiter bypass
0–5 Limiter knee
If this is on, only the low-fre-
quency band will be output.
If this is on, only the mid-fre-
OFF, ON
quency band will be output.
If this is on, only the high-fre-
OFF, ON
quency band will be output.
6 ms–46.0 s (fs=44.1 kHz), 5 ms–42.3 s (fs=48 kHz), 3 ms–23.0 s
(fs=88.2 kHz), 3 ms–21.1 s (fs=96 kHz)
01V96 Version 2—Owner's Manual
269
Description
Description