Yamaha O1V96 Owner's Manual page 265

DYNA. PHASER
Two input, two output dynamically controlled
phaser.
Parameter Range
Control source: input signal or
SOURCE INPUT, MIDI
MIDI Note On velocity
SENSE 0–100 Sensitivity
Upward or downward fre-
DIR. UP, DOWN
quency change
1
DECAY Decay speed
Lowest phase-shifted frequency
OFFSET 0–100
offset
Feedback gain (plus values for
normal-phase feedback, minus
FB.GAIN –99 to +99%
values for reverse-phase feed-
back)
2, 4, 6, 8, 10, 12,
STAGE Number of phase shift stages
14, 16
LSH F 21.2 Hz–8.00 kHz Low shelving filter frequency
LSH G –12.0 to +12.0 dB Low shelving filter gain
HSH F 50.0 Hz–16.0 kHz High shelving filter frequency
HSH G –12.0 to +12.0 dB High shelving filter gain
1. 6 ms–46.0 s (fs=44.1 kHz), 5 ms–42.3 s (fs=48 kHz), 3 ms–23.0 s
(fs=88.2 kHz), 3 ms–21.1 s (fs=96 kHz)
REV+CHORUS
One input, two output reverb and chorus effects in
parallel.
Parameter Range
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
THRU,
HPF High-pass filter cutoff frequency
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
LPF Low-pass filter cutoff frequency
THRU
Reverb and chorus balance (0%
REV/CHO 0–100%
= all reverb, 100% = all chorus)
FREQ. 0.05–40.00 Hz Modulation speed
AM DEPTH 0–100% Amplitude modulation depth
PM DEPTH 0–100% Pitch modulation depth
MOD. DLY 0.0–500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF, ON Tempo parameter sync on/off
Used in conjunction with
1
NOTE
TEMPO to determine FREQ.
1.
REV->CHORUS
One input, two output reverb and chorus effects in
series.
Description Parameter
REV TIME
INI. DLY
HI. RATIO
DIFF.
DENSITY
HPF
LPF
REV.BAL
FREQ.
AM DEPTH 0–100%
PM DEPTH 0–100%
MOD. DLY
WAVE
SYNC
NOTE
1.
REV+FLANGE
One input, two output reverb and flanger effects in
Description
parallel.
Parameter
REV TIME
INI. DLY
HI. RATIO
DIFF.
DENSITY
HPF
LPF
REV/FLG
FREQ.
DEPTH
MOD. DLY
FB. GAIN
WAVE
SYNC
NOTE
1.
Effects Parameters
Range Description
0.3–99.0 s Reverb time
0.0–500.0 ms Initial delay before reverb begins
0.1–1.0 High-frequency reverb time ratio
0–10 Spread
0–100% Reverb density
THRU,
High-pass filter cutoff frequency
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
Low-pass filter cutoff frequency
THRU
Reverb and chorused reverb bal-
0–100% ance (0% = all chorused reverb,
100% = all reverb)
0.05–40.00 Hz Modulation speed
Amplitude modulation depth
Pitch modulation depth
0.0–500.0 ms Modulation delay time
Sine, Tri Modulation waveform
OFF, ON Tempo parameter sync on/off
Used in conjunction with
1
TEMPO to determine FREQ.
Range Description
0.3–99.0 s Reverb time
0.0–500.0 ms Initial delay before reverb begins
0.1–1.0 High-frequency reverb time ratio
0–10 Spread
0–100% Reverb density
THRU,
High-pass filter cutoff frequency
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
Low-pass filter cutoff frequency
THRU
Reverb and flange balance (0% =
0–100%
all reverb, 100% = all flange)
0.05–40.00 Hz Modulation speed
0–100% Modulation depth
0.0–500.0 ms Modulation delay time
Feedback gain (plus values for
normal-phase feedback, minus
–99 to +99%
values for reverse-phase feed-
back)
Sine, Tri Modulation waveform
OFF, ON Tempo parameter sync on/off
Used in conjunction with
1
TEMPO to determine FREQ.
01V96 Version 2—Owner's Manual
265