Table of Contents

Advertisement

Send documentation comments to mdsfeedback-doc@cisco.com.
Cisco MDS 9216 Switch
Hardware Installation Guide
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel:
408 526-4000
800 553-NETS (6387)
Fax:
408 526-4100
Customer Order Number: DOC-7816165=
Text Part Number: 78-16165-01

Advertisement

Table of Contents
loading

Summary of Contents for Cisco MDS 9216

  • Page 1 Send documentation comments to mdsfeedback-doc@cisco.com. Cisco MDS 9216 Switch Hardware Installation Guide Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Customer Order Number: DOC-7816165= Text Part Number: 78-16165-01...
  • Page 2 You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: •...
  • Page 3 CCIP, CCSP, the Cisco Arrow logo, the Cisco Powered Network mark, Cisco Unity, Follow Me Browsing, FormShare, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST,...
  • Page 4 Send documentation comments to mdsfeedback-doc@cisco.com.
  • Page 5: Table Of Contents

    Opening a TAC Case xxiii TAC Case Priority Definitions xxiii Obtaining Additional Publications and Information xxiv Product Overview C H A P T E R Chassis Backplane Power Supplies Fan Module Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 6 Installing the Cisco MDS 9216 Switch C H A P T E R Pre-Installation Installation Guidelines Required Equipment Unpacking and Inspecting the Switch Installing the Chassis in the Rack Grounding the Chassis 2-15 Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 7 Removing an SFP Transceiver and Fiber Optic Cable 3-10 Maintaining SFP Transceivers and Fiber Optic Cables 3-10 Troubleshooting A P P E N D I X Getting Started Solving Problems at the Component Level Identifying Startup Problems Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 8 A P P E N D I X Switch Specifications Module Specifications Power Specifications Specifications for the Cisco MDS 9216 Power Supplies Component Power Requirements and Heat Dissipation Specifications Supported Power Supply Plugs Cable and Port Specifications A P P E N D I X...
  • Page 9 Send documentation comments to mdsfeedback-doc@cisco.com. Cisco Gigabit Ethernet / Fibre Channel Transceivers C-10 General Specifications for Cisco GE/FC SFP Transceivers C-11 Environmental and Electrical Specifications for Cisco GE/FC SFP Transceivers C-12 Cisco CWDM SFP Transceivers C-12 General Specifications for Cisco CWDM SFP Transceivers...
  • Page 10 Contents Send documentation comments to mdsfeedback-doc@cisco.com. Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 11: New And Changed Information

    Send documentation comments to mdsfeedback-doc@cisco.com. New and Changed Information The Cisco MDS 9216 Switch Hardware Installation Guide applies to all the Cisco MDS SAN-OS releases. Table 1 lists the new and changed features available with each Cisco MDS SAN-OS release for the Cisco MDS 9216 Switch, with the latest release first.
  • Page 12 New and Changed Information Send documentation comments to mdsfeedback-doc@cisco.com. Table 1 Documented Features for the Cisco MDS 9216 Switch Hardware Installation Guide (continued) Changed Where Feature Description in Release Documented Support for Support for connecting the 1.2(1a) Chapter 3: connecting...
  • Page 13 Table 2 lists the changes to the Cisco MDS 9216 Switch Hardware Installation Guide since it was released with part number 78-16165-01. If the document is updated with a new or revised part number, this table is cleared and only shows changes to the new document.
  • Page 14 New and Changed Information Send documentation comments to mdsfeedback-doc@cisco.com. Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 15: Preface

    Send documentation comments to mdsfeedback-doc@cisco.com. Preface This preface describes the audience, organization, and conventions of the Cisco MDS 9216 Switch Hardware Installation Guide. It also provides information on how to obtain related documentation. Audience To use this installation guide, you need to be familiar with electronic circuitry and wiring practices and preferably be an electronic or electromechanical technician.
  • Page 16: Document Conventions

    Cautions use the following conventions: Caution Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of data. Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 17 éviter les accidents. Pour prendre connaissance des traductions d’avertissements figurant dans cette publication, consultez le document Regulatory Compliance and Safety Information (Conformité aux règlements et consignes de sécurité) qui accompagne cet appareil. Cisco MDS 9216 Switch Hardware Installation Guide xvii 78-16165-01...
  • Page 18 Para ver as traduções dos avisos que constam desta publicação, consulte o documento Regulatory Compliance and Safety Information (Informação de Segurança e Disposições Reguladoras) que acompanha este dispositivo. Cisco MDS 9216 Switch Hardware Installation Guide xviii 78-16165-01...
  • Page 19: Related Documentation

    Refer to the following documents for additional information: Regulatory Compliance and Safety Information for the Cisco MDS 9000 • Family Cisco MDS 9500 Series and Cisco MDS 9216 Switch Quick Start Guide • Cisco MDS 9500 Series Hardware Installation Guide •...
  • Page 20: Obtaining Documentation

    These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the most current Cisco documentation on the World Wide Web at this URL: http://www.cisco.com/univercd/home/home.htm You can access the Cisco website at this URL: http://www.cisco.com...
  • Page 21: Documentation Cd-Rom

    Obtaining Documentation Send documentation comments to mdsfeedback-doc@cisco.com. Documentation CD-ROM Cisco documentation and additional literature are available in a Cisco Documentation CD-ROM package, which may have shipped with your product. The Documentation CD-ROM is updated regularly and may be more current than printed documentation.
  • Page 22: Obtaining Technical Assistance

    The Cisco TAC website (http://www.cisco.com/tac) provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The Cisco TAC website is available 24 hours a day, 365 days a year. Accessing all the tools on the Cisco TAC website requires a Cisco.com user ID and password.
  • Page 23: Opening A Tac Case

    For a complete listing of Cisco TAC contacts, go to this URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml TAC Case Priority Definitions To ensure that all cases are reported in a standard format, Cisco has established case priority definitions. Priority 1 (P1)—Your network is “down” or there is a critical impact to your business operations.
  • Page 24: Obtaining Additional Publications And Information

    Internetworking Terms and Acronyms Dictionary, Internetworking Technology Handbook, Internetworking Troubleshooting Guide, and the Internetworking Design Guide. For current Cisco Press titles and other information, go to Cisco Press online at this URL: http://www.ciscopress.com •...
  • Page 25 Obtaining Additional Publications and Information Send documentation comments to mdsfeedback-doc@cisco.com. • Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL: http://www.cisco.com/en/US/about/ac123/ac147/about_cisco_the_internet_...
  • Page 26 Preface Obtaining Additional Publications and Information Send documentation comments to mdsfeedback-doc@cisco.com. Cisco MDS 9216 Switch Hardware Installation Guide xxvi 78-16165-01...
  • Page 27: Product Overview

    The Cisco MDS 9216 Multilayer Fabric Switch supports storage area network (SAN) applications. It provides scalability, multi-transport capability, security and an easy way to manage enterprise SANs. The Cisco MDS 9216 Switch shares a consistent architecture with the Cisco MDS 9500 Series of multilayer directors, making it an intelligent and flexible fabric switch.
  • Page 28: Chassis

    Chapter 1 Product Overview Chassis Send documentation comments to mdsfeedback-doc@cisco.com. This chapter provides an overview of the Cisco MDS 9216 Switch, including the following information: Chassis, page 1-2 • Backplane, page 1-3 • Power Supplies, page 1-4 • • Fan Module, page 1-5 Supervisor Module, page 1-6 •...
  • Page 29: Backplane

    2 Switching module or services 4 Interface module module (such as IPS) Backplane The Cisco MDS 9216 backplane provides connectivity for the following modules, which plug directly into the backplane: One supervisor module with an integrated 16-port switching module. •...
  • Page 30: Power Supplies

    Power Supplies The Cisco MDS 9216 Switch supports dual hot swappable 845 Watt AC power supplies, each of which can supply sufficient power to the entire chassis should one power supply fail. The power supplies monitor their output voltage and provide status to the supervisor-fabric module.
  • Page 31: Fan Module

    Individual fans cannot be replaced, you must replace the entire fan module. The Cisco MDS 9216 Switch continues to run if the fan module is removed, as long as preset temperature thresholds have not been exceeded. This means you can swap out a fan module without having to bring the system down.
  • Page 32: Supervisor Module

    Supervisor Module The supervisor module provides the control and management functions for the Cisco MDS 9216 Switch, and includes an integrated 16-port switching module. The supervisor module provides multiple communication and control paths to avoid a single point of failure.
  • Page 33: Processor

    CompactFlash card that provides 256 MB of storage for software images. Supervisor Module LEDs Table 1-1 describes the LEDs for the Cisco MDS 9216 supervisor module. Table 1-1 LEDs for the Cisco MDS 9216 Fixed Supervisor Module with Integrated 16-Port Switching Module...
  • Page 34: Interface Module

    • management capabilities. RS-232 COM1 port with a DB-9 connector, which can be attached to a • modem. Figure 1-4 Interface Module for the Cisco MDS 9216 Switch CONSOLE MGMT 10/100 COM1 MDS 9216 1 ESD socket (for ESD strap)
  • Page 35: Interface Module Leds

    Chapter 1 Product Overview Interface Module Send documentation comments to mdsfeedback-doc@cisco.com. Interface Module LEDs Table 1-2 describes the LEDs provided on the Cisco MDS 9216 interface module. Table 1-2 LEDs on the Cisco MDS 9216 Interface Module Status Description Status Green All diagnostics pass.
  • Page 36: Switching Modules

    • 32-Port 1 Gbps / 2 Gbps Fibre Channel Switching Module The Cisco MDS 9216 Switch supports one hot-swappable switching or services module in addition to the 16-port 1 Gbps / 2 Gbps switching module that is part of the supervisor module.
  • Page 37: 32-Port 1 Gbps / 2 Gbps Fibre Channel Switching Module

    Product Overview Switching Modules Send documentation comments to mdsfeedback-doc@cisco.com. Figure 1-5 Cisco MDS 9000 Family 16-Port 1 Gbps / 2 Gbps Switching Module 1 Status LED 3 Link LED (to left of port) and speed LED (to right of port)
  • Page 38: Switching Module Features

    Product Overview Switching Modules Send documentation comments to mdsfeedback-doc@cisco.com. Figure 1-6 Cisco MDS 9000 Family 32-Port 1 Gbps / 2 Gbps Switching Module 1 Status LED 3 Link LED (to left of port) and speed LED (to right of port)
  • Page 39: Switching Module Leds

    Switching Module LEDs Table 1-3 describes the LEDs for the 16-port and 32-port switching modules. Table 1-3 LEDs for the Cisco MDS 9000 Family Fibre Channel Switching Modules Status Description Status Green All diagnostics pass.
  • Page 40: Fibre Channel Port Modes

    Chapter 1 Product Overview Switching Modules Send documentation comments to mdsfeedback-doc@cisco.com. Table 1-3 LEDs for the Cisco MDS 9000 Family Fibre Channel Switching Modules (continued) Status Description Link Solid green Link is up. Steady Link is up (beacon used to identify port).
  • Page 41: Ip Storage Services Module

    • TL—A translative loop port (TL port) connects a switch to a private loop. • For more information about supported port types, refer to the Cisco MDS 9000 Family Configuration Guide. IP Storage Services Module The IP Storage Services module (IPS module) provides eight ports of iSCSI and/or FCIP over Gigabit Ethernet, and supports the intelligent features available on other modules, including VSANs, security, and traffic management.
  • Page 42: Ports Configured To Run Fcip

    IP Storage Services Module Send documentation comments to mdsfeedback-doc@cisco.com. Figure 1-7 shows an IPS module. Figure 1-7 Cisco MDS 9000 Family IP Storage Services Module 1 Status LED 3 Link LEDs 2 Gigabit Ethernet ports 4 Asset tag Ports Configured to Run FCIP Ports configured for FCIP operation can be configured to support up to three virtual ISL connections (FCIP tunnels).
  • Page 43: Leds On Ip Storage Services Module

    IP Storage Services Module Send documentation comments to mdsfeedback-doc@cisco.com. LEDs on IP Storage Services Module Table 1-4 describes the LEDs for the IPS module. Table 1-4 LEDs for the Cisco MDS 9000 Family IP Storage Services Module Status Description Status Green All diagnostics pass.
  • Page 44: 32 Port Fibre Channel Advanced Services Module

    32 Port Fibre Channel Advanced Services Module The 32 Port Fibre Channel Advanced Services Module (ASM) for the Cisco MDS 9000 Family supports up to 32 Fibre Channel ports and provides distributed intelligent storage services such as network-based volume management and copy services, and is virtualization enabled. The module makes it possible to allocate bandwidth optimally and delivers the industry’s highest...
  • Page 45 If a single component or a set of components on the switching module fails, this failure will not disable another switching module if that is the only failure in the system. Cisco MDS 9216 Switch Hardware Installation Guide 1-19 78-16165-01...
  • Page 46 Link is healthy and beacon is enabled. green Intermittent Link is up and traffic is flowing through port. flashing green Solid orange Link is disabled by software. Flashing orange A fault condition exists. No link. Cisco MDS 9216 Switch Hardware Installation Guide 1-20 78-16165-01...
  • Page 47: Supported Sfp Transceivers

    Cisco SFP transceiver, refer to the SFP transceiver documentation. SFP transceivers can be ordered separately or with the Cisco MDS 9216. Use only Cisco SFP transceivers on the Cisco MDS 9216. Each Cisco SFP Note transceiver is encoded with model information that enables the switch to verify that the SFP transceiver meets the requirements for the switch.
  • Page 48: Combination Fibre Channel/Gigabit Ethernet Sfp Transceivers

    Specifications”. CWDM Combination Fibre Channel / Gigabit Ethernet SFP Transceivers All Fibre Channel and Gigabit Ethernet ports in the Cisco MDS 9216 support CWDM SFP transceivers. The Cisco CWDM SFP transceivers have LC connectors and support both Gigabit Ethernet and Fibre Channel (1 Gbps / 2 Gbps). They match the wavelength plan of Cisco CWDM GBICs and Cisco CWDM OADMs.
  • Page 49: Ethernet Ports

    Appendix C, “Cable and Port Specifications”. Ethernet Ports The IPS module supports 1-Gigabit Ethernet ports. For more information about supported port types, refer to the Cisco MDS 9000 Family Configuration Guide. Cisco MDS 9216 Switch Hardware Installation Guide 1-23 78-16165-01...
  • Page 50 Chapter 1 Product Overview Ethernet Ports Send documentation comments to mdsfeedback-doc@cisco.com. Cisco MDS 9216 Switch Hardware Installation Guide 1-24 78-16165-01...
  • Page 51: Chapter 2 Installing The Cisco Mds 9216 Switch

    Send documentation comments to mdsfeedback-doc@cisco.com. C H A P T E R Installing the Cisco MDS 9216 Switch This chapter describes how to install the Cisco MDS 9216 Switch and its components, and includes the following information: • Pre-Installation, page 2-2 Installing the Chassis in the Rack, page 2-7 •...
  • Page 52: Pre-Installation

    Planning and Maintenance Records”. • Ensure there is adequate space around the switch to allow for servicing the switch and for adequate airflow (airflow requirements are listed in Appendix B, “Technical Specifications”). Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 53 Avoid UPS types that use ferroresonant technology. These UPS types can become Caution unstable with systems like the Cisco MDS 9000 Family, which can have substantial current draw fluctuations because of fluctuating data traffic patterns. Ensure that circuits are sized according to local and national codes. For North •...
  • Page 54 A roof-mounted fan delivering 500 CFM is recommended but not – required. A minimum of 5 inches (12.7 cm) should be maintained between the roof – and the top of the highest piece of rack mounted equipment for airflow. Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 55 • Use the following screw torques: Captive screws: 4 in-lbs – – M3 screws: 4 in-lbs M4 screws: 12in-lbs – 10-32 screws: 20in-lbs – – 12-24 screws: 30in-lbs Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 56: Required Equipment

    Keep the shipping container for use when shipping the chassis in the future. Note If you purchased this product through a Cisco reseller, contact the reseller directly for technical support. If you purchased this product directly from Cisco, contact Cisco Technical Support at this URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.
  • Page 57: Installing The Chassis In The Rack

    • Installing the Chassis in the Rack This section describes how to install the Cisco MDS 9216 Switch in a rack using the rack mount kit provided in the accessory kit. If the rack is on wheels, ensure that the brakes are engaged or that the rack is Caution otherwise stabilized.
  • Page 58 Note If you purchased this product through a Cisco reseller, contact the reseller directly for technical support. If you purchased this product directly from Cisco, contact Cisco Technical Support at this URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.
  • Page 59 Installing the Cisco MDS 9216 Switch Installing the Chassis in the Rack Send documentation comments to mdsfeedback-doc@cisco.com. To install the Cisco MDS 9216 Switch in a rack, follow these steps: Install the L brackets as follows: Step 1 Position an L bracket against the chassis and align the screw holes as shown...
  • Page 60 Figure 2-2 Installing C Brackets onto the Cisco MDS 9216 Switch 1 C bracket 2 Screws, M4...
  • Page 61 Installing the Chassis in the Rack Send documentation comments to mdsfeedback-doc@cisco.com. Figure 2-3 Close-up of C Brackets for the Cisco MDS 9216 Switch Step 3 Position the chassis in the rack, inserting the rear of the chassis between the front...
  • Page 62 Installing the Cisco MDS 9216 Switch Installing the Chassis in the Rack Send documentation comments to mdsfeedback-doc@cisco.com. Figure 2-4 Installing the Cisco MDS 9216 Switch in the Rack 1 Mounting rail 3 Screws, 12-24 or 10-32 2 L bracket From the back of the rack, position the longer slider rails with the ears away from...
  • Page 63 Figure 2-5 Inserting and Installing Slider Rails (Back View) 1 Screws, 12-24 or 10-32 3 C bracket 2 Slider rail Figure 2-6 shows the Cisco MDS 9216 completely installed in a rack. Cisco MDS 9216 Switch Hardware Installation Guide 2-13 78-16165-01...
  • Page 64 Chapter 2 Installing the Cisco MDS 9216 Switch Installing the Chassis in the Rack Send documentation comments to mdsfeedback-doc@cisco.com. Figure 2-6 Cisco MDS 9216 Chassis Installed in the Rack Cisco MDS 9216 Switch Hardware Installation Guide 2-14 78-16165-01...
  • Page 65: Grounding The Chassis

    Figure 2-7 shows the system ground location on the Cisco MDS 9216 Switch. Cisco MDS 9216 Switch Hardware Installation Guide 2-15 78-16165-01...
  • Page 66 Installing the Cisco MDS 9216 Switch Grounding the Chassis Send documentation comments to mdsfeedback-doc@cisco.com. Figure 2-7 System Ground Location on the Cisco MDS 9216 Switch 1 ESD socket (on switch) 4 Screws, M4, with square cone washers 2 ESD plug...
  • Page 67: Starting Up The Switch

    Hazardous voltage or energy is present on the backplane when the system is Warning operating. Use caution when servicing. Statement 1034 During this procedure, wear grounding wrist straps to avoid ESD damage to the Caution switch. Cisco MDS 9216 Switch Hardware Installation Guide 2-17 78-16165-01...
  • Page 68: Connecting The Power Supplies

    Installing the Cisco MDS 9216 Switch Starting Up the Switch Send documentation comments to mdsfeedback-doc@cisco.com. Connecting the Power Supplies The Cisco MDS 9216 Switch supports 845 Watt AC power supplies, shown in Figure 2-8. Figure 2-8 Power Supply for the Cisco MDS 9216 Switch...
  • Page 69: Powering Up The Switch And Verifying Component Installation

    Do not connect the MGMT 10/100 Ethernet port to the LAN until the initial Note switch configuration has been performed. For instructions on configuring the switch, refer to the Cisco MDS 9000 Family Configuration Guide. Ensure that the switch is adequately grounded as described in the “Grounding the Step 6 Chassis”...
  • Page 70 Do not operate the switch without a functioning fan module except for during the Caution brief fan module replacement procedure. The Cisco MDS 9000 Family switches can operate for only a few minutes without a functioning fan module before they begin to overheat.
  • Page 71: Removing And Installing Components

    Installing the Cisco MDS 9216 Switch Removing and Installing Components Send documentation comments to mdsfeedback-doc@cisco.com. If you purchased this product through a Cisco reseller, contact the reseller directly Note for technical support. If you purchased this product directly from Cisco, contact Cisco Technical Support at this URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.
  • Page 72: Removing And Installing Switching And Services Modules

    This section describes how to install a switching or services module in slot 2 of the Cisco MDS 9216 Switch. Slot 1 is reserved for the supervisor module with its integrated 16-port switching module. Slot 2 can contain an optional 16-port or 32-port switching module or a services module such as an 8-port IPS module.
  • Page 73 Positioning the Module in the Chassis Insert module EMI gasket between slot guides EMI gasket DS -X9 032 STA TU S 1/2 G FC Mo dul e Ejector lever fully extended Cisco MDS 9216 Switch Hardware Installation Guide 2-23 78-16165-01...
  • Page 74 Removing and Installing Components Send documentation comments to mdsfeedback-doc@cisco.com. Figure 2-10 Clearing the EMI Gasket Amount of gap between the module EMI gasket and the module above it Press down Press down Cisco MDS 9216 Switch Hardware Installation Guide 2-24 78-16165-01...
  • Page 75: Removing A Switching Or Services Module From Slot 2

    Send documentation comments to mdsfeedback-doc@cisco.com. Removing a Switching or Services Module from Slot 2 This section describes how to remove a module from slot 2 in the Cisco MDS 9216 Switch. To remove a switching or services module from the chassis, follow these steps: Step 1 Disconnect any network interface cables attached to the module.
  • Page 76 Figure 2-11 Closing the Ejector Levers CONSOLE MGMT 10/100 COM1 MDS 9216 STATUS FAN-MOD-2 Ejector levers flush with module faceplate Do not press down too forcefully on the levers because they can bend. Caution Cisco MDS 9216 Switch Hardware Installation Guide 2-26 78-16165-01...
  • Page 77: Verifying Installation Of A Switching Or Services Module In Slot 2

    Cisco MDS 9000 Family Configuration Guide. Removing and Installing Power Supplies The Cisco MDS 9216 Switch supports dual 845 Watt AC power supplies that monitor output voltage and provide status to the supervisor module. Cisco MDS 9216 Switch Hardware Installation Guide...
  • Page 78: Removing A Power Supply

    Grasp the power supply handle with one hand and slide the power supply out of the chassis. Step 5 If the power supply bay is to remain empty, install a blank filler panel over the opening. Cisco MDS 9216 Switch Hardware Installation Guide 2-28 78-16165-01...
  • Page 79 Orient the power supply as shown in Figure 2-13, hold it by the handle and slide Step 4 the power supply into the power supply bay. Ensure that the power supply is fully seated in the bay. Cisco MDS 9216 Switch Hardware Installation Guide 2-29 78-16165-01...
  • Page 80 Fan Ok LED is green • • Output Fail LED is off If the LEDs indicate a power problem, see the “Troubleshooting the Power Supplies” section on page A-5 for troubleshooting information. Cisco MDS 9216 Switch Hardware Installation Guide 2-30 78-16165-01...
  • Page 81: Removing And Installing The Fan Module

    • You will need a flat-blade or no. 2 Phillips screwdriver to perform these procedures. Figure 2-14 shows a fan module partially installed in the Cisco MDS 9216 Switch. Figure 2-14 Fan Module M D S 92 16 Cisco MDS 9216 Switch Hardware Installation Guide...
  • Page 82: Removing A Fan Module

    Verify that the Fan Status LED is green. If the LED is not green, one or more fans are faulty. If this happens, contact your customer service representative for a replacement part. Cisco MDS 9216 Switch Hardware Installation Guide 2-32 78-16165-01...
  • Page 83 Installing the Cisco MDS 9216 Switch Removing and Installing Components Send documentation comments to mdsfeedback-doc@cisco.com. If you purchased this product through a Cisco reseller, contact the reseller directly Note for technical support. If you purchased this product directly from Cisco, contact Cisco Technical Support at this URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.
  • Page 84 Chapter 2 Installing the Cisco MDS 9216 Switch Removing and Installing Components Send documentation comments to mdsfeedback-doc@cisco.com. Cisco MDS 9216 Switch Hardware Installation Guide 2-34 78-16165-01...
  • Page 85: Chapter 3 Connecting The Cisco Mds 9216 Switch

    Caution strongly recommend that power cables and other potential noise sources be located as far away as practical from network cabling that terminates on Cisco equipment. In situations where long parallel cable runs cannot be separated by at least 3.3 ft (1 m), we recommend shielding any potential noise sources by housing them in a grounded metallic conduit.
  • Page 86: Preparing For Network Connections

    Connecting to a Fibre Channel Port, page 3-7 Preparing for Network Connections When preparing your site for network connections to the Cisco MDS 9216 Switch, consider the following for each type of interface, and gather all the required equipment before connecting the ports: Cabling required for each interface type •...
  • Page 87 To connect the console port to a computer terminal, the computer must support VT100 terminal emulation. The terminal emulation software—frequently an application such as HyperTerminal or Procomm Plus—makes communication between the Cisco MDS 9216 Switch and computer possible during setup and configuration. Figure 3-1...
  • Page 88: Connecting To The Com1 Port

    The COM1 port (labeled “COM1”) is an RS-232 port with a DB-9 interface. You can use it to connect to an external serial communication device such as a modem. For information about how to turn off hardware flow control, refer to the Cisco MDS 9000 Family Configuration Guide.
  • Page 89 DB-9 serial adapter labeled for use with the Cisco MDS 9216 Switch to the COM1 port, connect the RJ-45 to DB-25 modem adapter to the modem, then connect the adapters using the RJ-45 to RJ-45 rollover cable (or equivalent crossover cable).
  • Page 90: Connecting To The Mgmt 10/100 Ethernet Port

    To prevent an IP address conflict, do not connect the MGMT 10/100 Ethernet port Caution to the network until the initial configuration is complete. For configuration instructions, refer to the Cisco MDS 9000 Family Configuration Guide. The MGMT 10/100 Ethernet port (labeled MGMT 10/100) is autosensing and has an RJ-45 interface (Figure 3-3 on page 3-7).
  • Page 91: Connecting To A Fibre Channel Port

    Chapter 3 Connecting the Cisco MDS 9216 Switch Connecting to a Fibre Channel Port Send documentation comments to mdsfeedback-doc@cisco.com. Figure 3-3 Connecting to the MGMT 10/100 Ethernet Port on the Cisco MDS 9216 Switch CONSOLE MGMT 10/100 COM1 MDS 9216...
  • Page 92 2 inches if there is tension in the cable. Note Use only Cisco SFP transceivers on the Cisco MDS 9216 Switch. Each Cisco SFP transceiver is encoded with model information that enables the switch to verify that the SFP transceiver meets the requirements for the switch.
  • Page 93: Installing An Sfp Transceiver And Fiber Optic Cable

    Connect the other end of the cable to the external end system or switch. For instructions on verifying connectivity on a module port, refer to the Cisco MDS 9000 Family Configuration Guide. Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 94: Removing An Sfp Transceiver And Fiber Optic Cable

    Keep all optical connections covered when not in use. If they become dusty, • clean before using to prevent dust from scratching the fiber optic cable ends. Do not touch ends of connectors to prevent fingerprints and other • contamination. Cisco MDS 9216 Switch Hardware Installation Guide 3-10 78-16165-01...
  • Page 95 SFP transceiver. • Inspect routinely for dust and damage. If damage is suspected, clean and then inspect fiber ends under a microscope to determine if damage has occurred. Cisco MDS 9216 Switch Hardware Installation Guide 3-11 78-16165-01...
  • Page 96 Chapter 3 Connecting the Cisco MDS 9216 Switch Connecting to a Fibre Channel Port Send documentation comments to mdsfeedback-doc@cisco.com. Cisco MDS 9216 Switch Hardware Installation Guide 3-12 78-16165-01...
  • Page 97: Appendix

    Send documentation comments to mdsfeedback-doc@cisco.com. A P P E N D I X Troubleshooting This appendix describes how to troubleshoot the Cisco MDS 9216 Switch installation, and includes the following information: • Getting Started, page A-1 Solving Problems at the Component Level, page A-2 •...
  • Page 98: Solving Problems At The Component Level

    Fan Module” section on page 2-31. • The system software boots successfully. Refer to the Cisco MDS 9000 Family Configuration Guide for information on booting the system and initial configuration tasks. The supervisor module and the switching or services module are installed •...
  • Page 99: Identifying Startup Problems

    Troubleshooting Identifying Startup Problems Send documentation comments to mdsfeedback-doc@cisco.com. If you purchased this product through a Cisco reseller, contact the reseller Note directly for technical support. If you purchased this product directly from Cisco, contact Cisco Technical Support at this URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.
  • Page 100 A-7). Verify that the terminal is set correctly and that it is connected properly to the Step 4 supervisor module console port if the boot information and system banner are not displayed. Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 101: Troubleshooting The Power Supplies

    If you are unable to resolve the problem or if you determine that either a power supply or backplane connector is faulty, contact your customer service representative (see the “Contacting Customer Service” section on page A-6). Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 102: Troubleshooting The Fan Module

    If the Status LED on a module is orange, the module might be busy or disabled. Refer to the Cisco MDS 9000 Family Configuration Guide to configure or enable the interfaces. After the system re-initializes the interfaces, the Status LED on the module should be green.
  • Page 103: Contacting Customer Service

    “Obtaining Technical Assistance” in the Preface. If you purchased this product through a Cisco reseller, contact the reseller directly Note for technical support. If you purchased this product directly from Cisco, contact Cisco Technical Support at this URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml.
  • Page 104 Appendix A Troubleshooting Contacting Customer Service Send documentation comments to mdsfeedback-doc@cisco.com. Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 105: Appendix

    Specifications for cables and connectors are provided in Appendix C, “Cable and Port Specifications”. Switch Specifications Table B-1 lists the environmental specifications for the Cisco MDS 9216 Switch. Table B-1 Environmental Specifications for the Cisco MDS 9216 Switch Description Specification Temperature, ambient operating 32 to 104°F (0 to 40°C)
  • Page 106: Appendix B Technical Specification

    Altitude, operating -197 to 6500 ft (-60 to 2000 m) Noise levels 70 dB Table B-2 lists the physical specifications for the Cisco MDS 9216 Switch. Table B-2 Physical Specifications for the Cisco MDS 9216 Switch Description Specification Dimensions 5.25 x 17.5 x 22.75 inches (13.3 x 44.5 x 57.8 cm)
  • Page 107: Module Specifications

    Module Specifications Send documentation comments to mdsfeedback-doc@cisco.com. Module Specifications Table B-3 lists the specifications for the Cisco MDS 9216 supervisor module (which is fixed in the chassis) and the switching and services modules. Table B-3 Cisco MDS 9216 Module Specifications...
  • Page 108: Specifications For The Cisco Mds 9216 Power Supplies

    Component Power Requirements and Heat Dissipation Specifications Consider heat dissipation when sizing the air-conditioning requirements for an installation. The power and heat associated with a Cisco MDS 9216 Switch varies based upon the following considerations: Switching module type and number of switching modules installed •...
  • Page 109 Table B-6 provides a sample calculation of power and heat dissipation for the following hardware configuration at maximum wattage: Cisco MDS 9216 chassis, including two 845 Watt AC power supplies • • Fixed supervisor module, with 16 Fibre Channel ports One 32-port Fibre Channel switching module.
  • Page 110: Supported Power Supply Plugs

    IEC C15 connector on the end that plugs into the switch. Only the power cords provided with the switch are supported. Note Figure B-1 shows the supported power supply plugs for the Cisco MDS 9216 Switch. Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 111: Supported Power Supply Plugs

    (13A; replaceable fuse) 3 Australia, New Zealand 7 South Africa SAA/3 plug, AS/NZS 3112-1993 (10A) EL 208, SABS 164-1 (10A) 4 Europe 8 Switzerland VIIG Plug, CEE (7) VII (16A) 12G SEV 1011 (10A) Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 112 Appendix B Technical Specifications Supported Power Supply Plugs Send documentation comments to mdsfeedback-doc@cisco.com. Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 113: Appendix

    • • SFP Transceiver Specifications, page C-8 Cables and Adapters Provided The Cisco MDS 9216 Switch accessory kit includes the following items: • RJ-45 to RJ-45 rollover cable RJ-45 to DB-9 female DTE adapter (color-coded green and labeled “FOR •...
  • Page 114: Console Port

    DTE adapter or the RJ-45 to DB-9 female DTE adapter to connect the console port to a computer running terminal emulation software. Console Port Pinouts Table C-1 lists the pinouts for the console port on the Cisco MDS 9216 Switch. Table C-1 Console Port Pinout Signal 1.
  • Page 115: Connecting The Console Port To A Computer Using The Db-25 Adapter

    (labeled “Terminal”) to connect the console port to a computer running terminal emulation software. Table C-3 lists the pinouts for the console port, the RJ-45 to RJ-45 rollover cable, and the RJ-45 to DB-9 female DTE adapter. Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 116: Com1 Port

    The COM1 port is not supported for connection to a console. Connecting the COM1 port to a modem is supported only for switches running Note Cisco MDS SAN-OS Release 1.2(1a) or later. Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 117: Com1 Port Pinouts

    RJ-45 to RJ-45 rollover cable. Note Use the green DB-9 adapter that is specifically labeled for use with the Cisco MDS 9216 Switch. If this adapter is not included in the accessory kit, you can request one from your customer service representative. Table C-5 lists the pinouts for the COM1 port, the RJ-45 to DB-9 adapter, RJ-45 to RJ-45 rollover cable, and the RJ-45 to DB-25 male DCE adapter.
  • Page 118: Mgmt 10/100 Ethernet Port

    You can use a modular, RJ-45, straight-through UTP cable to connect the management port to an external hub, switch, or router (see Figure C-1). Figure C-1 RJ-45 Interface Cable Connector RJ-45 (both ends) 1 Pin 1 2 Pin 8 Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 119 1 TXD+ 1 RXD+ 2 TXD- 2 RXD- 3 RXD+ 3 TXD+ 6 RXD- 6 TXD- 4 NC 4 NC 5 NC 5 NC 7 NC 7 NC 8 NC 8 NC Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 120: Sfp Transceiver Specifications

    For detailed specifications, refer to the documentation provided with the transceivers. Use only Cisco SFP transceivers on the Cisco MDS 9216 Switch. Each Cisco SFP transceiver is encoded with model information that enables the switch to verify that the SFP transceiver meets the requirements for the switch. Refer to the release notes for the list of specific supported SFP transceivers.
  • Page 121: General Specifications For Cisco Fibre Channel Sfp Transceivers

    SFP Transceiver Specifications Send documentation comments to mdsfeedback-doc@cisco.com. General Specifications for Cisco Fibre Channel SFP Transceivers Table C-8 lists general specifications for Cisco Fibre Channel SFP transceivers. Note The cable distances provided are for 2 Gbps. Table C-8 General Specifications for Cisco Fibre Channel SFP Transceivers...
  • Page 122: Environmental And Electrical Specifications For Cisco Fibre Channel Sfp Transceivers

    Table C-10 lists the combination Gigabit Ethernet / Fibre Channel (GE/FC) SFP transceivers available through Cisco. Table C-10 Cisco Gigabit Ethernet / Fibre Channel SFP Transceivers Description Type 1 Gbps Ethernet and 1 Gbps/2 Gbps Fibre Channel-SW SFP, LC Short wavelength...
  • Page 123: General Specifications For Cisco Ge/Fc Sfp Transceivers

    SFP Transceiver Specifications Send documentation comments to mdsfeedback-doc@cisco.com. General Specifications for Cisco GE/FC SFP Transceivers Table C-11 lists general specifications for Cisco combination Gigabit Ethernet / Fibre Channel SFP transceivers. The cable distances provided are for 2 Gbps. Note Table C-11 General Specifications for Cisco Gigabit Ethernet/Fibre Channel...
  • Page 124: Environmental And Electrical Specifications For Cisco Ge/Fc Sfp Transceivers

    Table C-13 Cisco CWDM SFP Transceivers Description Color Cisco CWDM SFP 1470 nm; Gigabit Ethernet and 1Gbps/2Gbps FC Gray Cisco CWDM SFP 1490 nm; Gigabit Ethernet and 1Gbps/2Gbps FC Violet Cisco CWDM SFP 1510 nm; Gigabit Ethernet and 1Gbps/2Gbps FC Blue Cisco CWDM SFP 1530 nm;...
  • Page 125: General Specifications For Cisco Cwdm Sfp Transceivers

    Table C-13 Cisco CWDM SFP Transceivers (continued) Description Color Cisco CWDM SFP 1570 nm; Gigabit Ethernet and 1Gbps/2Gbps FC Orange Cisco CWDM SFP 1590 nm; Gigabit Ethernet and 1Gbps/2Gbps FC Red Cisco CWDM SFP 1610 nm; Gigabit Ethernet and 1Gbps/2Gbps FC Brown...
  • Page 126: Optical Specifications For Cisco Cwdm Sfp Transceivers

    Appendix C Cable and Port Specifications SFP Transceiver Specifications Send documentation comments to mdsfeedback-doc@cisco.com. Table C-16 provides the electrical specifications for CWDM SFP transceivers. Table C-16 Electrical Specifications for Cisco CWDM SFP Transceivers Parameter Symbol Minimum Typical Maximum Units Supply...
  • Page 127 Appendix C Cable and Port Specifications SFP Transceiver Specifications Send documentation comments to mdsfeedback-doc@cisco.com. Table C-17 Optical Specifications for Cisco CWDM SFP Transceivers Parameter Symbol Min. Typical Max. Units Notes Transmitter Central (x-4) (x+1) (x+7) Available Wavelength center wavelengths: 1470, 1490,...
  • Page 128 Appendix C Cable and Port Specifications SFP Transceiver Specifications Send documentation comments to mdsfeedback-doc@cisco.com. Cisco MDS 9216 Switch Hardware Installation Guide C-16 78-16165-01...
  • Page 129: Appendix

    Chassis and Module Information, page D-5 Note For information about how to query the switch for configuration information, refer to the Cisco MDS 9000 Family Configuration Guide. Site Preparation Checklist Planning the location and layout of your equipment rack or wiring closet is essential for successful switch operation, ventilation, and accessibility.
  • Page 130 Receptacle proximity to the equipment • Dedicated circuit for power supply Dedicated (separate) circuits for • redundant power supplies for power failures • Grounding evaluation: • Circuit breaker size CO ground (AC- powered systems) • Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 131 1. Verify that the power supply installed in the chassis has a dedicated AC source circuit. 2. UPS = uninterruptible power supply. 3. EMI = electromagnetic interference 4. RFI = radio frequency interference. Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 132: Contact And Site Information

    Use the following worksheet to record contact and site information. Table D-2 Contact and Site Information Contact Person Contact Phone Contact Email Building/Site Name Data Center Location Floor Location Address (line 1) Address (line 2) City State Zip Code Country Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 133: Chassis And Module Information

    Contract Number_______________________________________________ Chassis Serial Number___________________________________________ Product Number________________________________________________ Table D-3 Network-Related Information Switch IP Address Switch IP Netmask Host Name Domain Name IP Broadcast Address Gateway/Router Address DNS Address Modem Telephone Number Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 134 Chassis and Module Information Send documentation comments to mdsfeedback-doc@cisco.com. Table D-4 Module Information Slot Module Type Module Serial Number Notes Supervisor Note The supervisor module and the interface module are not removable. Cisco MDS 9216 Switch Hardware Installation Guide 78-16165-01...
  • Page 135: I N D E X

    LEDs 1-19 connecting pinouts console port cabling connecting backplane pinouts description conventions binary images document downloading 1-19 customer service contacting CWDM transceivers description 1-22 cabinet installation SFP transceiver specifications C-12 guidelines Cisco MDS 9216 Switch Hardware Installation Guide IN-1 78-16165-01...
  • Page 136 Ethernet ports chassis 2-15 IP Storage Services module 1-23 MGMT 10/100 port heat dissipation specifications fan module description removing and installing 2-31 troubleshooting interface module FCIP description configuring ports 1-16 LEDs Cisco MDS 9216 Switch Hardware Installation Guide IN-2 78-16165-01...
  • Page 137 MGMT 10/100 port modes Fibre Channel 1-14 maintenance power-on records front panel LEDs 1-19 MGMT 10/100 port power supplies cabling description connecting removing and installing 2-27 pinouts specifications supported plugs troubleshooting Cisco MDS 9216 Switch Hardware Installation Guide IN-3 78-16165-01...
  • Page 138 2-17 self-test passed supervisor module front panel LEDs 1-19 description self-test running installing 2-22 front panel LEDs 1-19 LEDs services module processor specifications removing 2-25 troubleshooting specifications supervisor modules LEDs 1-19 Cisco MDS 9216 Switch Hardware Installation Guide IN-4 78-16165-01...
  • Page 139 2-25 specifications troubleshooting switching modules downloading binary image 1-19 transceivers supported SFP transceivers 1-21 troubleshooting component level contacting customer service fan module power supplies startup problems switching and services modules Cisco MDS 9216 Switch Hardware Installation Guide IN-5 78-16165-01...
  • Page 140 Index Send documentation comments to mdsfeedback-doc@cisco.com. Cisco MDS 9216 Switch Hardware Installation Guide IN-6 78-16165-01...

Table of Contents