Series Programs - Toshiba Strata CIX Programming Manual

Telephone Button Programming

500 Series Programs

500 Series Programs
Table 1-35 Programs 500~577
Button Sequence
500 System Call Forward
Assignment
500 Hold
,
500-00 SCF Number
Hold
n,
500-01 Call Type
FB01 Hold
, n,
500-02 Period
FB02 Hold
, n,
500-03 Telephone Status
FB03 Hold
, n,
500-04 Destination 1
FB04 Hold
, n,
501
System Speed Dial
Assignment
501 Hold
,
501-00 Speed Dial Bin
Hold
n,
501-01 Number
FB01 Hold
, n,
501-02 Name
FB02 Hold
, n,
502 Terminal Paging
Group Assignment
502 Hold
,
502-00 Primary DN
Hold
n,
502- PG01~PG16
01~16
FB01 FB16
~ , n,
1-74
Value(s)
n = 1~4 (CTX100)
1~10 (CTX670 Basic)
1~32 (CTX670 Exp.)
n = 1. CO Loop Ground
2. DID
3. Tie
4. Ring Transfer
5. Internal
n = 1. Day
2. Day2
3. Night
n = 1. Busy
2. Off No Answer
3. Busy No Answer
4. DND
n = Up to 32 digits
Hold
,
n = 000~799
n = Up to 32 digits, 0~9, *, #
and Pauses
n = Up to 8 digits
Hold
,
n = Up to 5 digits
n = 1. On
2. Off (default)
Hold
Summary
This assignment is used to configure up to 32 system call forward
patterns. Station DNs are assigned to these patterns in the station
COS assignments.
Note The Administrator programs the condition of transfer by
setting Call Type, Period and Telephone Status. Destinations
1 and 2 should be programmed after transfer conditions are
set.
Select the SCF pattern number to configure.
Select the type of call that should forward in this pattern.
Note Each 500-01 call type must be the same telephone status.
Also, all calls must be the same Call Forward type.
Select the system time period in which this SCF pattern should
operate.
Select the telephone DN status that should cause this SCF pattern to
operate.
Note Each 500-01 call type must be the same telephone status.
Also, all calls must be the same Call Forward type.
Select the first destination to which the call should forward.
System Speed Dial consists of up to 800 pre-programmed numbers
each containing up to 32 digits. If the number being entered exceeds
the 32 digits, the next speed dial location will automatically be
appended to create longer numbers. One other speed dial location
can be nested within the number for dialing a common routine with
the number (see ì516 Station Speed Dialî on page 5-31 for more
information about nesting).
Enter the speed dial bin location.
This is the dialable number stored in the speed dial bin.
Note To enter pauses enter Px, where x equals 1~9 (seconds),
which is the length of the pause.
This is the Name that appears on Telephone LCD dial directories.
Note This feature is available in CTX WinAdmin and Strata
DKT30xxSD only.
Assigns Primary DNs to Paging Group(s).
Enter the Primary DN of the station to be assigned to Paging Groups.
A station may belong to more than one paging group.
Note You can have upto 72 paging groups in the Strata CTX100
and upto 120 paging groups in the Strata CTX670. Any
software release before R1.01, M19 supports only 32 paging
groups for all systems.
Activate the Paging Group(s) this station belongs too. The number of
DNs that can be assigned are 1~4 (CTX100), 1~8 (CTX670 Basic),
1~16 (CTX670 Exp.)
Strata CIX/CTX Telephone Button Programming 11/04