Memory Operation; General Description; Programming A Memory Channel - Icom IC-2300H Instruction Manual

Previous view
5

MEMORY OPERATION

■ General description

The transceiver has 207 memory channels including 6
scan edge memory channels (3 pairs), and 1 Call chan-
nel. These channels can be individually programmed
with:
• Operating frequency (p. 5)
• Duplex direction (p. 12) and offset (p. 15)
• Subaudible tone or tone squelch and tone frequency
(pp. 13, 39–41)
• Skip setting* (p. 32)
In addition, a total of 10 memory banks; A to J, are se-
lectable for use by groups, and so on.
*except for scan edge memory channels.
■

Programming a memory channel

The VFO settings, including the Set mode contents
such as subaudible tone frequency, and so on, can be
programmed into a memory channel.
q Set the desired frequency in the VFO mode.
w Push [S.MW].
• The " " icon and the memory channel number blink.
e Rotate [DIAL] to select the memory channel to be
programmed.
• If the selected channel is blank, only the memory
channel number is displayed.
r Hold down [MW] (S.MW) for 1 second to program.
• 3 beeps sound.
• The memory channel number increases, when
continuing to hold down [MW] (S.MW) after pro-
gramming.
✔CONVENIENT
Memory programming can be performed in several
ways. Example; Programming the memory channel to
the same (or different) memory channel, memory chan-
nel to the Call channel, and so on.
Using the HM-133V
z Set the desired frequency in the VFO mode.
x Push [FUNC]
, and then push [MW]
• The " " icon and the memory channel number blink.
c Push [Y] or [Z] to select the memory channel to be
programmed. (direct numeric input cannot be used.)
v Push [FUNC]
, and then hold down [MW]
1 second to program.
➥ 3 beeps sound and the VFO contents (including
the subaudible tone frequency, and so on.) are
programmed.
➥ The memory channel number increases, when
continuing to hold down [MW]
ming.
[i.e.]: Programming 145.870 MHz into memory chan-
Push [V/MHz].
MUTE
NAR
MID
LOW
LOCK
S ET
Rotate [DIAL] to set the frequency.
MUTE
NAR
MID
LOW
LOCK
S ET
Push [S.MW].
MUTE
NAR
MID
LOW
LOCK
S ET
Rotate [DIAL] to select the memory channel to be programmed.
MUTE
NAR
MID
LOW
LOCK
S ET
Hold down [S.MW] for 1 second.
MUTE
NAR
MID
LOW
LOCK
S ET
MUTE
NAR
MID
LOW
LOCK
S ET
[i.e.]: Programming 145.870 MHz into the memory
Push
MUTE
NAR
MID
LOW
LOCK
S ET MONI
Push
MUTE
NAR
MID
LOW
LOCK
S ET
MONI
Push
MUTE
NAR
MID
LOW
LOCK
S ET MONI
.
Push
MUTE
NAR
MID
LOW
for LOCK
S ET MONI
Push
MUTE
LOCK
S ET MONI
after program-
MUTE
NAR
MID
LOW
17 LOCK
S ET MONI
nel 20 via the front panel.
DIGITAL PRIO AO BUSY
ANM DUP T-SCAN PRIO SCAN
MONI LOW TONE M/CALL V/MHz
DIGITAL PRIO AO BUSY
ANM DUP T-SCAN PRIO SCAN
MONI LOW TONE M/CALL V/MHz
DIGITAL PRIO AO BUSY
ANM DUP T-SCAN PRIO SCAN
MONI LOW TONE M/CALL V/MHz
DIGITAL PRIO AO BUSY
ANM DUP T-SCAN PRIO SCAN
MONI LOW TONE M/CALL V/MHz
DIGITAL PRIO AO BUSY
ANM DUP T-SCAN PRIO SCAN
MONI LOW TONE M/CALL V/MHz
Beep Beep Beep
DIGITAL PRIO AO BUSY
ANM DUP T-SCAN PRIO SCAN
MONI LOW TONE M/CALL V/MHz
channel 20, using the microphone.
.
DIGITAL PRIO AO BUSY
SCAN
ANM DUP T-SCAN PRIO
LOW TONE M/CALL V/MHz
DIGITAL PRIO AO BUSY
ANM DUP T-SCAN PRIO SCAN
TONE M/CALL V/MHz
LOW
, and then .
DIGITAL PRIO AO BUSY
ANM DUP T-SCAN PRIO SCAN
LOW TONE M/CALL V/MHz
/ .
DIGITAL PRIO AO BUSY
ANM DUP T-SCAN PRIO SCAN
LOW TONE M/CALL V/MHz
, and then hold down for 1 second.
DIGITAL PRIO AO BUSY
ANM DUP T-SCAN PRIO SCAN
LOW TONE M/CALL V/MHz
Beep Beep Beep
DIGITAL PRIO AO BUSY
ANM DUP T-SCAN PRIO SCAN
LOW TONE M/CALL V/MHz
.