Programming Channel Names - Icom IC-2300H Instruction Manual

Previous view
5
MEMORY OPERATION

■ Programming channel names

Each memory channel and the Call channel can be
programmed with an alphanumeric channel name, for
easy recognition. Names can be a maximum of 6 char-
acters— see the table to the right, for the selectable
characters.
q Push [M/CALL] to select the memory mode.
w Rotate [DIAL] to select the desired memory channel.
e Hold down [ANM] (MONI) for 1 second to switch the
channel name display.
• Two beeps sound.
• The name is displayed, if programmed.
r Push [SET] to enter the channel name programming
mode.
t Rotate [DIAL] to select a character.
• The selected character blinks.
y Push [SET] or [MONI] to move the cursor to the left
or right.
u Repeat steps t and y, until the desired channel
name is completed.
i Push any key other than [SET] or [MONI], to pro-
gram the name and exit the channel name program-
ming mode.
• To switch to the frequency display, hold down
[MONI] (ANM) for 1 second again.
IMPORTANT!: While the channel name display
mode is selected, and when [SET] is pushed, the
channel name programming mode is always ac-
cessed.
To access the Set mode, cancel the channel name
display by holding down [MONI] (ANM) for 1 second.
Using the HM-133V
z Select the memory or Call channel to be assigned
the memory name.
x Push [FUNC]
, and then push [ANM]
• The name is displayed, if programmed.
c Push [SET]
.
v Push [Y] or [Z] to select the desired character.
• The selected character blinks.
b Push [SET]
or [ENT]
the left or right.
n Repeat steps v and b until the desired channel
names are completed.
m Push [CLR]
to program the name and exit the
channel name programming mode.
, If desired, push [FUNC]
to return to the frequency display.
.
to move the cursor to
, and then push [ANM]
(B) (C) (D)
(A)
(K) (L) (M) (N)
(V) (W) (X)
(U)
(5)
(6) (7) (8)
(%) (()
(&)
(')
(/) (:) (;) (<)
(]) (^) (space)
[i.e.]: Programming "CLUB" into memory channel 5.
Select memory channel 5, and then hold down [ANM] (MONI) for 1 second.
DIGITAL PRIO AOBUSY
MUTE
NAR
MID
LOW
LOCK ANM DUP T-SCAN PRIO
S ET
MONI LOW TONE M/CALL
Push [SET].
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK ANM DUP T-SCAN PRIO
S ET MONI LOW TONE M/CALL
Rotate [DIAL] to select the character,
and then push [SET] or [MONI] to move the cursor.
PRIO AO BUSY
ANM DUP PRIO
M/CALL
S ET MONI LOW
Repeat until the name is complete.
Push any other keys than [SET] or [MONI].
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK ANM DUP T-SCAN PRIO
S ET MONI LOW TONE M/CALL
[i.e.]: Programming "CLUB" into memory channel 5.
Select memory channel 5, push
DIGITAL PRIO AOBUSY
MUTE
NAR
MID
LOW
LOCK ANM DUP T-SCAN PRIO
S ET MONI LOW TONE M/CALL
Push .
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK ANM DUP T-SCAN PRIO
S ET
MONI LOW TONE M/CALL
Push / to select the character,
and then push or
PRIO AO BUSY
PRIO
ANM DUP
M/CALL
S ET MONI LOW
Repeat until the name is complete.
Push .
DIGITAL PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK ANM DUP T-SCAN PRIO
S ET MONI LOW TONE M/CALL
21
(G) (H)
(E) (F)
(O) (P) (Q) (R)
(Y) (Z)
(1) (2)
(9)
(0)
(!) (")
())
(✱) (+) (,)
(>) (?)
(=) (@)
Channel name display
(The name is displayed, if programmed.)
SCAN
V/MHz
SCAN
V/MHz
PRIO AO BUSY
MUTE
NAR
MID
LOW
LOCK ANM DUP
SCAN
S ET MONI LOW
V/MHz
SCAN
V/MHz
then .
Channel name display
(The name is displayed, if programmed.)
SCAN
V/MHz
SCAN
V/MHz
to move the cursor.
MUTE
NAR
MID
LOW
LOCK ANM DUP
SCAN
S ET MONI LOW
V/MHz
SCAN
V/MHz
(I) (J)
(S) (T)
(3) (4)
(#) ($)
(–) (.)
([) (\)
PRIO SCAN
M/CALL V/MHz
PRIO AO BUSY
PRIO SCAN
M/CALL V/MHz