U Menu/Group Keys [Menu/Grp] (P - Icom IC-7000 Instruction Manual

✔ What is the PBT control?
PBT electronically narrows the IF passband width to reject
interference. This transceiver uses DSP to implement PBT.
➥ While M-ch/RIT is selected:
● Rotate the inner control to select a memory
channel (p. 100).
● Hold down inner control for 1 second to turn
the RIT/∂TX mode ON (pp. 73, 86).
• Push [Z( /
menu grp
● While the RIT/∂TX mode is OFF:
Rotate the outer control to select a memory
bank (p. 104).
● While the RIT/∂TX is ON:
Rotate the outer control to shift the receive or
transmit frequency (pp. 73, 86).
• " " or " " indicators appear when the RIT or
∂TX function is activate.
• The shift frequency range is ± 9.999 kHz in 1 Hz
∂TX
steps (or ±9.99 kHz in 10 Hz steps).
RIT
M-ch
Channel Channel
decreases increases
• When the RIT or ∂TX function is ON, hold down
[F-1 RIT] or [F-2 ∂TX] for 1 second to add or
subtract the frequency shift to the display fre-
quency.
✔ What is the RIT function?
RIT (Receiver Incremental Tuning) shifts the receive fre-
quency without shifting the transmit frequency.
This is useful for fine tuning for stations calling you off fre-
quency or when you prefer to listen to slightly different-
Decreases
sounding voice characteristics.
✔ What is the ∂TX function?
M-ch
The ∂TX shifts the transmit frequency without shifting the
Channel
receive frequency. This is useful for simple split frequency
increases
operation in CW.
Channel
decreases
)] to exit the RIT/∂TX mode.
RIT
M-ch
RIT
Frequency Frequency
decreases increases
Increases
Frequency
decreases
y TWIN PBT (M-ch/RIT) INDICATOR
(pp. 73, 77, 86, 100)
➥ Indicates the status of [PBT/M-ch/RIT] (t) as
the Twin PBT function or memory channel/RIT
control.
• Indicator is green when the Twin PBT function is se-
lected.
• Indicator is off when the M-ch/RIT control is se-
lected.

u MENU/GROUP KEYS [MENU/GRP] (p. 151)

➥ Push either key one or more times to select menus
within a menu group (M, S or G (Graphic)).
➥ Hold down for 1 second to select one of the three
menu groups: M-1 to M-3, S-1 to S-3 and G-1
(Scope) to G-3 (SWR meter).
i TUNER/CALL KEY [TUNER/CALL]
➥ During HF/50 MHz operation (p. 114):
● Push momentarily to toggle the automatic an-
tenna tuner function ON or OFF.
• An optional antenna tuner must be connected.
• " " indicator appears when the tuner is ON.
● Hold down for 2 seconds to manually tune the
antenna.
• An optional antenna tuner must be connected.
• " " indicator appears when the tuner is ON.
➥ During 144/430 MHz operation (p. 100):
Push momentarily to select the call channel (or
return to the previous channel/frequency when
the call channel is already selected).
• "C1" is the 144 MHz call channel and "C2" is the 430
MHz call channel.
o MULTI-FUNCTION KEYS [F-1]/[F-2]/[F-3]/[F-4]
➥ Push to select the function indicated in the LCD
display above these keys. (pp. 5–8, 151)
• Functions vary depending on the active menu.
RIT
Frequency
increases
Functions appear
See the illustration of the Front panel on page i-2.
2