JVC RX-8040B Instructions Manual page 58

I Operating JVC's Audio/Video Components
You can operate JVC's audio and video components with this receiver's remote control, since control signals for JVC
components are preset in the remote control.
• Refer also to the manuals supplied with your video components.
IMPORTANT:
To operate JVC's audio components usina this remote control:
• You need to connect JVC's audio components through the COMPU
LINK (SYNCHRO)jacks (see page 51) in addition to the
connections using cables with RCA pin plugs (see pages 10 and
11).
• Aim the remote control directly at the remote sensor on the
receiver.
• To operate a source with the remote control, the source must be
selected using source selecting buttons on the remote control.
• To operate the cassette deck or MD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 24.)
When using the remote control:
- Set the ZONE l/ZONE 2 selector to ZONE 1 or ZONE 2 correctly.
-Check the indication shown on the remote's display when you press
a button--this indicates the remote control operation mode together
with multi-room operation mode (either for ZONE 1 or ZONE 2) for
about two hours.
-The CONTROL button can change the remote control operation
mode without changing the source.
Each time you press the button, the remote control operation mode
changes in the sequence as follows:
VCR1 --* TAPE --* CDR --* CDDSC --* (back to the beginning)
@ O
ZONE1 ZONE2 ZONE1 ZONE2
Ex. When you press CD with
ZONE l/ZONE 2 selector
set to ZONE 1.
Ex. When you press CD with
ZONE l/ZONE 2 selector
set to ZONE 2.
Sound control section [Amplifier]
You can always perform the following operations:
AUDIO POWER ON : Turn oil the receiver.
AUDIO POWER STANDBY: Turn off the receiver.
ZONE 1 ON/OFF
ZONE 2 ON/OFF
ANALOG/DIGITAL
BASS BOOST
MIDNIGHT MODE
EX/ES/PLllx
SURROUND
DSP
SURR/DSP OFF
CC CONVERTER
ANALOG DIRECT
SLEEP
DIMMER
MUTING
VOLUME +/-
: Turn oil or offthe Zone 1 sound,
: Turn oil or off the Zone 2 sound.
: Switch the analog and digital input
alternately.
: Turn oil or off Bass Boost.
: Select the Midnight Mode.
: Select the EX/ES/PLIIx
reproduction mode.
: Turn oil and select the Surround
modes.
: Turn oil and select the DSP modes.
: Turn off the Surround/DSP modes.
: Turn oil or off CC Converter.
: Turn oil or off Analog Direct.
: Set the Sleep Timer.
: Dim or brighten the display.
: Turn oil or off sound muting.
: Adjust the volume level.
After pressing SOUND, you
TEST
FRONT.L then LEVEL +/-
FRONT.R then LEVEL +/-
CENTER then LEVEL +/-
SUBWFR then LEVEL +/-
SURR'L then LEVEL +/-
SURR'R then LEVEL +/-
SURR BK then LEVEL +/-
EFFECT
LIVENESS
call perform tile following operations:
Turn oil or off the test tone output.
Adjust the left front speaker output
level.
Adjust the right front speaker output
level.
Adjust tile center speaker output
level.
Adjust the subwoofcr output level.
Adjust the left surround speaker
output level.
: Adjust the right surround speaker
output level.
: Adjust the surround back speaker
output level.
: Select the effect level.
: Select the liveness.
Tuner
You can always perform the following operations:
FM : Select tile FM band.
AM : Select tile AM baud.
After pressing FM or AM, you call perform the following operations:
1 - 10, +1 0 : Select a preset chanuel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press +10, then 10.
TUNING UP/DOWN : Tulle in to stations.
FM MODE
: Change tile FM reception mode.
Notes:
• After adjusting sounds, press the corresponding source selecting
button to operate your target source by using the !0 keys;
otherwise, the !0 keys cannot be used for operating your target
source.
• When you press the FRONToL, FRONToR, CENTER, SUBWFR,
SURR,L, SURR,R, or SURR BK button, the corresponding speaker
name appears on the remote's display.
56