JVC RX-8040B Instructions Manual page 34

l Basic Settings
Some of the following settings are required after connecting and positioning your speakers while others will make
operations easie_ You can use QUICK SPEAKER SETUP to easily set up your speaker configuration.
Basic setting operations are only possible while the receiver is ready for Zone 1 operations.
IMPORTANT:
Check the following before or while using the buttons and controls.
For Zone 1 operations:
The ZONE 1 indicator lights up on the unit's display.
• When using the unit:
-"ZONE2" is not shown in the unit's main display.
3. Press in MULTI JOG (PUSH SET).
"ROOM SIZE'?" appears on tile display, then the initial room
size setting appears.
(ii_[ _ ,"' r-' "r' i i r",
.:::,[::. [ "...i-"
VOLUME
r", ,'-, ,'-, ".A ,"- "r '-:=i-" .", _ _-_t S
i'=:. i ..i i..i ['i .':' .i. ='.'..i.':. :' I
!
an_
(ii_ _
,:7 [:: "F [ [ [::,
...:i.... i =.."i
sp-_rs 1
....................... VCkUME
L..' I I I I IYI I1
I
I I |..I I 1.: L.. _
1:1=_.lL--
= -. ".,,- ".,,- = = "- =,.,, = = = -, -,,.= L,.
[']!1l_ _ [-%'Fq_ ,_'J b"]'J"trl _
Quick Speaker Setup helps you to easily and quickly register the
speaker size and speaker distance according to your listening room
to create the best possible surround effect.
• You can also register each speaker's information manually.
For details, see page 34.
Before you start, remember...
There is a time limit ill doing the l_llowing steps. If tile setting is
canceled before you finish, start from step 1 again.
1. Press QUICK SPEAKER SETUE
"SETUP" and "SPEAKERS?" appear on the display, then the
initial setting for the total number of tile connected speakers
(channels) appears.
I ana_0G
SPEAKERS I
VOLUME
,-"5
."" i......r, i i i....
::::, [ :::. [ U 1"'
,'-'- ='-', ='-" .'-, = ." r'- =-'-. ,-"- ,-'.
"': i"' i" M i':. P" i":""': ."
=" r'- "l" i ll"=
"it'= i ill"
VOkUmE
........................ r' __n
"::,"" 1":.. ; i:::,,, i:'i i....""
2. Turn MULTI JOG to select an appropriate
number of the connected speakers (speaker
channel number).
As you turn the jog, the speaker channel number changes as
follows.
• For the details of speaker channel number, see "Speakers
(channels) number and the size" on page 33.
4. TUrn MULTI JOG to select an appropriate room
size to match to your listening room.
As you turn the jog, the room size changes as follows,
• To select your appropriate room size, see "Room size and the
speaker distance" on page 33.
a_aLO_
i::.r'.."_ i...i;;/,i ,', i'<i"i i"
i',, =,,,: :,,,= l i
SMALL __ MID __ LARGE".' __ (Back to the beginning)
* "LARGE" is the initial setting.
.
Press in MULTI JOG (PUSH SET).
"COMPLETE" appears on the display, then goes back to tile
source indication.
• Speaker configuration settings now become active.
I I
1_, _ "" "" "" ' ' ""
'....i... i i ii...'
.... • I.... : '.." I sPEa_r_ _ vOLuME
:"" :": 1".'1 l": i r" "r' 1'-' _ -i I-
L.. L.: 1"11-"L.. 1:::. [ 1::.
c _n
Notes:
• This procedure will not be completed if you stop in the middle of the
setting process.
• Once Quick Speaker Setup is performed, the speaker output levels
are also set to appropriate values automatically (common to all
sources), ff you want to set the speaker output levels separately for
each source, see "Adjusting the speaker output levels" on page 40.
_os
,::' i:::' "T'i i ,.':,
.-=i.... i :...=i
I
* "6.0CH" is the initial setting.
32