JVC RX-8040B Instructions Manual page 22

Press one of the source selection buttons.
• When you have connected digital source components using the
digital terminals, change the input lnode for these components to
the digital input mode (see page 22).
Ex. When VCR 1 is selected as the source.
Selected source name
_0G J ...........
"." ;..' |"..l.
;.. i i i..= i...= i if... i...
._: ,'_: "'.. "'.. ............................................... ,'...," " i
The current Surround/DSP mode appears.
SPEA_RSI I
VOLUUE
2'-,
On the front panel
• The lamp on the selected source lights up (ex. when VCR 1 is
selected as the source).
(?K) _ _ (SK)
_ (2_ (?K) (2D
On the remote
Notes:
• When connecting an MD recorder (to the TAPE/MD IN jacks), and a
DBS tuner (to the TV SOUND/DBS IN jacks), change the source
names shown on the display. For details, see "Changing the Source
Name" on page 24.
• When you press one of the audio source selection buttons
(PHONO, CD, TAPE/MD, CDR, FM crAM) on the remote control,
the receiver automatically turns on. If you turn on the receiver with
the ZONE !/ZONE 2 selector set to ZONE 2, press
ZONE 1 ON/OFF to activate Zone ! operations.
- While Zone ! is deactivated, press one of the audio source
selection buttons on the remote control with the ZONE !/ZONE 2
selector set to ZONE 1 to activate Zone 1 operations.
• When you select DVD MULTI, you can enjoy analog discrete output
sound (5. !-channel surround reproduction) from the external
component.
- You may need to select analog discrete output mode on the
external component.
- When using the headphones, you can listen to the front channel
sounds (left and right) only.
- The Surround modes (see page 42) and DSP modes (see page
48) cannot be applied to DVD MULTI playback mode.
Speaker and signal indicators on the display
By checking the following iudicators, you can easily confirm which
speakers you are activating and which signals are coming into this
receiver.
Speaker indicators
ISUBWFRI
r-q r-q
Signal indicators
LFE
LS S RS
SB
What speaker indicators light depends on the speaker setting
(For details, see "Setting the speakers" on page 34.)
• The fralnes of "L," "C," "R," "LS," "RS," and "SB" light up, when
the corresponding speakers are set to "LARGE" or "SMALL" and
when the speaker is required for the Surround/DSP nlode currently
selected.
• When "SUB WOOFER" is set to "YES," _ lights up (see
page 34).
• All three frames on the row of"SB" are not used at the same time.
When "SBACK OUT" is set to "2SPK," the left and the right ones
are used. When it is set to "1SPK," the nliddle one is used (see
page 34).
The signal indicators light up to show the incoming signals.
L:
• When digital input is selected: Lights up when the left
channel signal comes in.
• When analog input is selected: Always lights up.
R: • When digital input is selected: Lights up when the right
channel signal comes in.
• When analog input is selected: Always lights up.
C: Lights up when the center channel signal comes in.
LFE: Lights up when the LFE channel signal comes in.
LS: Lights up when the left surround channel signal comes in.
RS: Lights tip when the right surrouud channel signal comes in.
S: Lights up when the monaural surrouud channel signal
COllies ill.
SB: Lights up when the surround back channel signal comes in.
Note:
When DVD MULTI is selected as the source, "L," "C," "R," "LFE," "LS,"
and "RS" light up.
How to understand the speaker and siqnal indicator
illumination
SB
Ex. No sound comes out of the
center speaker and surround
back speakers though center
channel and surround back
channel signals are coming
into this receiver.
2O