JVC RX-8040B Instructions Manual page 66

No sound effect such as tile Surround
mode, DSP mode and equalization
pattern.
DVD MULTI is selected as the source
(equalization pattern is effective).
Activate all connected speakers correctly.
(See "Setting the speakers" on page 34.)
Turn off Analog Direct. (See page 23.)
Select tile source other than DVD MULTI.
(See page 2(t.)
PROBLEM POSSIBLE CAUSE SOLUTION
Multi-channel reproduction mode ZONE 2 SPEAKERS are activated. Deactivate the Zone 2 front speakers.
call,lot be used for Zolle 1 sources.
Expected SUH'ound effect cannot be Speakers are deactivated on the Quick "_
obtained. Speaker Setup or the Basic Setting. =
e_
Analog Direct is turned on. _,
"DOLBY D EX," "ES DSCRT." or Software itself is not Dolby Digital EX ol Play back software bearing the mark Dolby a_"
"ES MATRIX" cannot be select as the DTS-ES software, or "EX/ES/PLIIx" setting Digital EX or DTS-ES and set m =
Surround mode. is not correct. "EX/ES/PLIIx" setting to "AUTO" or "ON."
(See page 45.)
Tile display does not light up. The power cord is not plugged in. Plug the power" cord into an AC outlet.
Noise is heard during record playing. A ground cable of the turntable is not Connect it to the screw marked (rb).
connected to the screw marked (_).
Howling during record playing. Your turntable is too close to speakers. Move speakers away from tile turntable.
"NO SUBWFR" appears on the SUBWOOFER OUT ON/OFF is pressed If subwoofer is connected, set "SUB
display,, while "SUB WOOFER" is set to "NO." WOOFER" to "YES" so that SUBWOOFER
OUT ON/OFF works.
"OVERLOAD" starts flashing on the
display,.
Speakers are overloaded because of high
volume either in Zone 1 or in Zone 2.
I. Press O/1 STANDBY/ON on the front
panel to turn off the receiver.
2. Stop tile playback source.
3. Turn on tile receiver again, and adjust tile
volmne.
Speakers are ox erloaded because of a short
circuit of tile speaker" terminals.
Press O/I STANDBY/ON on the front panel
to turn off the receiver, then check the
speaker" wiring.
If "OVERLOAD" does not disappear,
unplug the AC power cord, then plug it back
again.
If speaker wiring is not short-circuited,
contact your dealer.
No playback picture of the VCR I or Setting of the component video input are not Set tile component video input setting
DBS tuner call be viewed, done for correctly. ("VIDEO IN DBS" and "VIDEO IN VCRI")
correctly. (See page 38.)
DVD MULTI is cannot be select as the ZONE 2 SPEAKERS are activated. Deactivate the Zone 2 front speakers.
source.
"DSP NC," starts flashing on the The built-in microcomputer is not Press _/I STANDBY/ON on the front panel
display, functioning correctly, to turn off the receiver. After unplugging the
AC power cord, contact your dealer'.
The STANDBY lamp goes off after Very high voltage or very low voltage is Press ¢,3/ISTANDBY/ON on the front panel
turning on the power, but soon the applied to the unit, or built-in power to turn off the receiver. At_er unplugging the
receiver turns off again (into standby amplifier becomes out of order'. AC power cord, consult your dealer'.
mode).
Remote control does not work. The ZONE I/ZONE 2 selector is not set Set the selector correctly either to "ZONE 1"
correctly, or to "ZONE 2."
The TV operation mode selector is not set Set tile selector correctly either to "TV" or to
correctly. "CATV/DBS."
RF communication between the receiver and Consult your dealer.
the remote control is interrupted from
outside.
Renlote COlltrol
does not work
properly.
Batteries are weak.
Incorrect remote control operation mode is
selected.
Replace batteries. (See page 15.)
Select tile correct remote control operation
mode. (See pages 56 to 61 .)
r_
64