JVC RX-8040B Instructions Manual page 33

21NiNl i vtr j
Once a station is assigned to a channel number, the station can be
quickly tuned irr. You cart preset up to 30 FM arrd 15 AM stations.
To store the preset stations
Before you start, remember...
There is a time limit in doing tire following steps. If tire setting is
canceled before you finish, start from step 2 again.
1. TUne in to the station you want to preset
(see
"Tuning in to Stations Manually").
• If you want to store the FM reception mode t_r this station,
select the FM reception mode you want. See "Selecting tire
FM Reception Mode" on the right column.
2. Press MEMORY.
_o_ +U_ED STEeEO AVTOUUTING
i::' i'.d ....... v _a,,
i i i .........
sP_s i
,= .. .... ......... :,,:
,::, i'
..: ....i
['i["i.._:.
i
Tire channel number position starts flashing on tire display for
about 10 seconds.
3. Press FM/AM PRESET • or • to select a
channel nnmber while the channel nnmber
position is flashing.
julep STEeEO AUTOUUnN_
r- i':'i "'i
i ; I "
._. % sPr_s i VOLUME
•-. "", .-- , . ... -r
4. Press MEMORY again while the selected channel
number is flashing on the display.
Tire selected channel number stops flashing.
Tire station is assigned to tire selected channel number.
5. Repeat steps 1 to 4 nntil yon store all the stations
you want.
To erase a stored preset station
Storing a new station on a used number erases tire previously stored
one.
To tune in to a preset station
On the front oanel:
1. Press FM or AM to select the band.
The last received station of the selected band is tuned irr.
2. Press FM/AM PRESET • or • until yon find the
channel yon want.
On the remote control:
1. Press FM or AM to select the band.
The last received station of the selected band is tuned irr.
2. Press the 10 keys to select a preset channel
number.
• For channel number 5, press 5.
• For channel number 15, press +10 then 5.
• For channel number 20, press +10 then 10.
• For channel number 30, press +10, +10, then 10.
Notes:
• You can only select the same station of the same band (FM or AM)
for both Zone ! and Zone 2 operations. If you change the station for
Zone 2, it also changes for Zone ! (and vice versa: indications on
the unit_ display also change). This also means that if you change
the station for Zone 2 while recording a broadcasting program in
Zone !, recording in Zone ! will be interrupted.
• When the !0 keys do not work for selecting a preset channel
number, press FM or AM on the remote control so that the remote
control can be used for tuner operation.
o
o
o
When an FM stereo broadcast is hard to receive or noisy, you can
change the FM reception mode while receiving an FM broadcast.
• You can store the FM reception mode for each preset station.
While listening to an FM station, press FM MODE.
• Each time you press tire button, the FM reception mode alternates
between "AUTOMUTING" arrd "MODE MONO."
AUTOMUTING
MODE MONO
Normally select this.
When a program is broadcasted in stereo, you
,:,,ill hear stereo sound; when in monaural, you
will hear monaural sounds.
This mode is also useful to suppress static
noise between stations.
The AUTO MUTING indicator lights up on
the display. (Initial setting)
Select this to improve the reception (but
stereo effect will be lost).
In this mode, you will hear noise while tuning
in to the stations.
The AUTO MUTING indicator (and the
STEREO irrdicator) goes off from the display.
Note:
When you use the FM MODE on the remote control, be sure that it is
activated for the tuner, not for the DVD and others.
31