JVC RX-8040B Instructions Manual page 42

I:b't"q_ I:/'¢tl'g_,P_'_.
Before you start, remember...
There is a time limit in doing the l_llowing steps. If the setting is
canceled before you finish, start from step 1 again.
Ex. When adjusting the subwoofer level to "-3."
1. Press ADJUST.
The last selected item appears on the display.
ANAUa_
iC r,.i or.,,
_BW_R] L': J'.': [,.'J
SPEAKERS
VOLUME
III" iI'I. i "I "IT I I
i-, i. i i,.,, "., i,-i "::' _ -I r
J........ .........." Ja...
C 21
2. Turn MULTI JOG until an item you want
appears on the display.
• In tiffs example, select "SUBWFR LVL." For available items,
see the list "Basic Adjustment Items" on page 39.
[)_ "-, • i "-,
/_: i,. . j :,2 i,,.j
SPEAKERS
VOLUME
........................ =_S
"-.i ii"iiliP" i'.:" i i..ii r_ I
3. Press in MULTI JOG (PUSH SET).
The current setting (or level) for the selected item appears on the
display.
{_ r'., i i r'.,
i.. . j .',,.J i ...J
_PEAKEHS I VOLUME
"" ' ' "" ' ' "" "" ¢':" _ In S :::, U [::5 [.i.[ "" [',:: E."
4. TUrn MULTI JOG to select a setting you want or
to make an adjustment as you like.
i".. i i i".,
suB_i ii- "I "ii " I iii"I
S'_A_RS
iiii iimll i [.i ri.i ii.p _ ___L_E__:.i]
.::, "J [:::,".L" "" P:. "" ...:,
5. Press in MULTI JOG (PUSH SET).
6. Repeat steps 2 to 5 to set other items if necessary.
7. Press EXIT.
The source indication resumes on the display.
Adjusting the equalization patterns
You can adjust the equalization patterns to your preference.
• Once you have made an adjustment, it is memorized for each
source.
• The equalization pattern affects the front speaker sounds only.
• Eoualization adiustment--EO 63Hz. EO250Hz.
EQ lkHz, EQ 4kHz, EQ16kHz
You can adjust five frequencies (63 Hz, 250 Hz, l kHz, 4 kHz,
16 kHz) within the range of-8 dB to +8 dB ("0 (dB)" is the
initial setting) in 2 dB steps.
• When an adjustment is made, the D.EQ indicator lights up on
the display.
To flat the equalization pattern, set all the frequencies to
"0 (dB)" in step 4 of "Basic Procedure" on the left column.
The D.EQ indicator goes off from the display.
Note:
When Analog Direct is in use, Equalization patterns are not
available.
Adjusting the speaker output levels
You can ad.iust the speaker output levels.
• Once you have made an adjustment, it is memorized for each
source.
• Adiustable speakers
You can adjust the following speakers' output levels within the
range of-10 dB to +10 dB ("0 (dB)" is the initial setting):
SUBWFR LVL Select to adjust the subwoofer output level.
FRNT L EVE Select to adjust the left front speaker output
level.
FRNT R EVE Select to adjust the right front speaker output
level.
CENTER LVL Select to adjust the center speaker output
level.
SURR L LVL Select to adjust the left surround speaker
output level.
SURR R EVE Select to adjust the right surround speaker
output level.
SBACK EVE Select to adjust the surround back speaker
output level.
Notes:
• If you have selected "NO" or "NONE" for a speaker (see page
34), the output level for the corresponding speaker is not
adjustable.
• Speaker output levels (except the subweefer output level) are
net adjustable when Analog Direct is in use. But when you
canceled the subwoofer output using the SUBWOOFER OUT
ON/OFF button (see page 22), you also cannot adjust the
subweefer output level.
40