Electrical Requirements - Fisher & Paykel Dryer Installation Instructions Manual

Electrical Requirements for Electric Models Only
Usea new UL/_SA approved 30._ampereDower cord or direct wire
cab[co
Usea ULapproved strain re[[efo
Disconnect Dower before making e[ectrk:a[ connect[onso
Connect neutral wire (white or center wire) to center terminal
On a[[ four wire installations remove 'the grounding [ink and
connect the ground wire to the green ground connecting screw°
Connect remaining 2 supply wires to remaining 2 terminalso
Securely tighten a[[ electrical connections°
Failure to do socan result in death, fire, or electrical shock°
!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
iiiilililililililililililililil
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!
!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
iiiilililililililililililililil
iiiilililililililililililililil
iiiilililililililililililililil
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
iiiilililililililililililililil
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
iiiilililililililililililililil
iiiiiiiiiiiiiiii
!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!
!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!
!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
iiiilililililililililililililil
iiiiiiiiiiiiiiii
!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i!
iiiilililililililililililililil
!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i! 22
Note:
The wiring diagram is inside the control console.
The dryer must be plugged into or
connected to an individual branch circuit,
do not use an extension cord.
Ensure proper ground exists before use.
The power supply must be 220/240V or
208V,60 Hz approved alternating current
electrical service. The electrical service
requirements carl be found on the data
label that is located or] the console back.
A 30 ampere fuse or circuit breaker is
required or] each of the lines.
if local codes permit, an external
ground wire (not provided),
which meets local codes, may
be added by attaching to the
green ground screw on the rear
of the dryer, and to a grounded
metal cold water pipe or other
established ground.
Ifa power cord is used, the cord must be plugged into a 30 ampere receptacle.
The power cord is NOT provided with U.S. e lectric model dryers.
This dryer is supplied with the cabinet grounded through the neutral or] the terminal block. If
the dryer is to be installed in (1) a new branch installation, (2) a mobile home, (3) a recreational
vehicle, (4) an area where local codes do not permit grounding through the neutral conductor,
the appliance grounding link must be removed and a 4 wire power cord/cable or a separate
grounding wire must be used.
Do not reuse a power supply cord/cable from an old dryer. The power cord/cable electric supply
wiring must be retained at the dryer cabinet with a suitable UL listed strain relief.