Fisher & Paykel DE4560M Installation Instructions Manual
Hide thumbs
Also See for DE4560M:
- Installation manual (40 pages) ,
- Installation manual/user manual (40 pages)
Table of Contents
Advertisement
Quick Links
Installation Instructions
Read and follow the 'Safety and warnings' and 'Installation instructions' sections carefully before using your
dryer!
Accessories
Please check you received the following accessories with your Fisher & Paykel dryer. You will find them inside the drum:
• 1 x Installation guide/User guide
• 1 x Inverted panel
• 1 x Duct adapter
• 1 x Wall mounting kit
Unpacking
To ensure the best performance from your new dryer please follow the instructions below.
Remove All Packaging Before Use
1. Remove the outer packaging (including the polystyrene packer and plastic wrapping).
• Ensure packaging materials are kept out of reach of children.
• Help protect the environment and dispose of the packaging from around the dryer in an
https://producthelp.fisherpaykel.com/au/Dry/Dryers/Vented/DE4560M1/User_Guide_DE4560M1/03_Installation_Instructions
environmentally friendly manner.
Updated: Thu, 27 Jan 2022 05:02:50 GMT
Powered by
1
Advertisement
Table of Contents
Related Manuals for Fisher & Paykel DE4560M
Summary of Contents for Fisher & Paykel DE4560M
- Page 1 Installation Instructions Read and follow the ‘Safety and warnings’ and ‘Installation instructions’ sections carefully before using your dryer! Accessories Please check you received the following accessories with your Fisher & Paykel dryer. You will find them inside the drum: • 1 x Installation guide/User guide •...
- Page 2 2. Tilt the dryer backwards and ‘walk’ it off the base one foot at a time. Not doing so may cause damage to your floor and dryer. 3. Remove all packaging and accessories from inside the drum and ensure you remove protective covers from the door and console.
-
Page 3: Internal Venting
External Venting Your dryer has been designed to be vented outside to provide the following advantages: • Ensures optimum efficiency by preventing recirculation of moist air. • Eliminates condensation on walls and ceilings. • Reduces the chance of lint being sucked into the dryer. •... -
Page 4: Freestanding Venting Options
Freestanding The dryer stands on the floor and can easily be moved into position. 1. Move the dryer into the desired position. Do not lift the dryer by the top panel. 2. Have a minimum clearance on all sides of at least 20mm. 3. -
Page 5: Inverted Wall Mounting Installation
to ensure the ducting is not restricted with tight bends or can be crushed. Internal Venting Front venting is the only recommended option for venting into the room. The dryer is set up for front venting when it leaves the factory. Where possible all efforts should be made to vent the dryer externally to avoid moisture build up around the dryer. -
Page 6: Inverted Wall Mounting
Inverted Wall Mounting https://producthelp.fisherpaykel.com/au/Dry/Dryers/Vented/DE4560M1/User_Guide_DE4560M1/03_Installation_Instructions Updated: Thu, 27 Jan 2022 05:02:50 GMT Powered by... -
Page 7: Wall Mounting
6. Fit inverted control panel over the existing panel. 7. Adjust the display to read correctly on an inverted panel: ◦ For DE7060M, DE6060M and DE5060M press for three seconds. ◦ For DE4560M press for three seconds. https://producthelp.fisherpaykel.com/au/Dry/Dryers/Vented/DE4560M1/User_Guide_DE4560M1/03_Installation_Instructions Updated: Thu, 27 Jan 2022 05:02:50 GMT Powered by... -
Page 8: External Venting Options
◦ The dryer will beep to indicate you have made a correct selection, and the display will change after three seconds. ◦ Repeat the same steps to return the panel to the factory setting. Before a rear venting option is installed the dryer must be changed from the front venting factory setup. Remove the outlet grille from the front left-hand side and replace with the outlet cover from the rear left-hand side. -
Page 9: Electrical Connection
Electrical Connection 1. This appliance must be connected to a 220V – 240V, 50Hz, sinusoidal, 10A electrical supply. 2. Uncoil the power cord, remove and discard the plastic pin cover and plug into a power socket. 3. Connect the appliance to an earthed outlet protected by a fuse of suitable capacity. -
Page 10: Installation Test Cycle
Installation Test Cycle Ensure the installation test cycle is completed before you dry any items in your dryer. This checks your dryer is installed correctly and functioning properly prior to use. 1. Turn your dryer on by pressing ‘POWER’ 2. Select the ‘Time Dry’ cycle for 30 minutes. Ensure the drum is empty and the door is closed (you will hear it click shut). -
Page 11: Product Specifications
Product Specifications DE5060M DE4560M DE6060M DE7060M DE5060MU Capacity (kg)* Dimensions (mm) Width Depth Height Electrical Volts 220 – 240 220 – 240 220 – 240 220 – 240 Amps (maximum) Rated Power (W) 1750 1750 1750 1770 * Capacity refers to the maximum dry weight of items the dryer can dry at any one time.