Alarm Key/Sw Tamper; Reporting Options; Report Pin Retry; Report Exit Error - Bosch Solution 6000-IP Installation Manual

Solution 6000-IP
Installation Manual

turned off (disarmed) before the entry delay time expires,
an alarm will occur.

Alarm Key/Sw Tamper

This option allows you to sound an alarm when a tamper
condition occurs on a zone programmed as a keyswitch
input. Refer to MENU 3-1-1 — Zone Type for information
on programming zones to be a keyswitch input.
Areas > Area Properties >

Reporting Options

1

Report PIN Retry

2

Report Exit Error

3

Smart Lockout

4 Reserved
5

Cancel Report

6 Reserved
7

Op/Cl In Part On

8

Op/Cl After Alarm

The above options are programmable per area.
1) Enter [MENU] + [2] + [1] + [4] and select the area
from the list then press [OK].
2) Use the up and down arrow keys to highlight the
option then press the [ON] key to enable or the
[OFF] key to disable.
 Report PIN Retry
 Report Exit Error
Smart Lockout
Press OK ON OFF MENU

3) Repeat Step 2 until all options are programmed as
required, then press [OK] to save and exit or press
[MENU] to exit without saving.
Report PIN Retry
When the PIN retry count as programmed in MENU 1-5-1
is reached, a 'Wrong Code Entry' alarm report will be sent
to the control room.
Report Exit Error
This option allows the system to report an 'Exit Error'
alarm report.
An exit error occurs when an entry/exit delay zone
becomes unsealled during exit delay time and remains
unsealled at the end of exit delay time. If this happens,
the entry delay will start. If the area is not turned off
(disarmed) before the entry delay time expires an 'Exit
Error' alarm report will be sent.
Smart Lockout
Smart lockout allows a previously locked zone to
reactivate during the siren run time when a new alarm
event occurs.
6-6
Area Programming

MENU 2-1-4

Y
Y
N
N
Y
N
N
N
Cancel Report
When set, a 'Cancel' report will be sent if a user disarms
the area before the siren timer expires.
Op/Cl In Part On
When set, the panel will send 'Open' or 'Close' reports
when the area has been turned Part On or Part 2 On.
Op/Cl After Alarm
When set, the panel will only send an 'Open' or 'Close'
report after an alarm has occured. This report will be sent
for all users regardless of whether or not they have been
programmed to send open/close reports.
Areas > Area Properties >

Strobe Trigger

1

Audible Burglary

2

Silent Burglary

3

Fire Alarm

4 Keyfob On/Off
5 Keyswitch On/Off
6
Reserved
7 24Hr Alarm
8 Reserved
Programming any of these options allow the strobe
output to operate when the corresponding event
occurs. The strobe light must be connected to an output
programmed as a event type 48 for it to operate. See
Section 8 — Output Programming for more information
on output event types.
1) Enter [MENU] + [2] + [1] + [5] and select the area
from the list then press [OK].
2) Use the up and down arrow keys to highlight the
option then press the [ON] key to enable or the
[OFF] key to disable.
 Audible Burglary
Silent Burglary
 Fire Alarm
Press OK ON OFF MENU

3) Repeat Step 2 until all options are programmed as
required, then press [OK] to save and exit or press
[MENU] to exit without saving.
Audible Burglary
When selected, the panel will activate the strobe output
when an audible burglary zone has triggered an alarm.
Silent Burglary
When selected, the panel will activate the strobe output
when a silent burglary zone has triggered an alarm.
Fire Alarm
When selected, the panel will activate the strobe output
 MENU 2-1-5
Bosch Security Systems 10/22 BLCC615I
Y
N
Y
N
N
N
Y
N