Alpha Text; Clock Programming; Getting Started With Myalarm; Service Mode - Bosch Solution 6000-IP Installation Manual

Solution 6000-IP Installation Manual

A L P H A T E X T
Text descriptions are available for Area Name, Zone Name,
User Name, TimeZone Name, Holiday Name, Keypad/
Reader Name and Output Name. Each name can have a
maximum of 20 characters.
Area Name A2
Reception Area
Press ◄►

When programming text, each numeric key represents a
different group of characters.
Pressing the same numeric key repeatedly will step you
through the available characters assigned to the key. The
text key layout is the same as most phones. Refer to the
table below for detailed character information.
Key Characters Assigned To Each Numeric Key
1 . , ?
2 A B C
3 D E F
4
G H I
5 J K L
6 M N O
7 P Q R
8 T U V
9 W X Y
0 SPACE 0

Scroll Up through entire character list

Scroll Down through entire character list
 Move to left one character position
 Move to right one character position
OFF Clear from cursor postiion to end of line
Table 13: Text Keypad Character Set
Once the desired character is displayed press the right
arrow key to move to the next character position.
To save programming changes, press [OK] or press [MENU]
to exit without saving.
The following additional special characters are
i
available by scrolling using the up and down arrow keys.
Note
+ - @ # $ " & % * : ( ) / < > =
C LO C K P R O G R A M M I N G
Use the left and right arrow keys to move to the field and
use the up and down keys to change. Press [OK] to save or
[MENU] to exit without saving.
i The time is set using a 24 hour clock.
Note
Set Date And Time
01-Jan-2015 12:00
i
Press

4-2
Programming Overview

OK or MENU
! - & ` 1
a b c 2
d e f 3
g h i 4
j k l 5
m n o 6
S p q r s
t u v 8
Z w x y z
OK to SAVE
G E T T I N G S TA R T E D W I T H M YA L A R M
To get the panel registered onto the MyAlarm platform
follow these steps.
1) Panel from factory setting
2) Establish an IP connection using Ethernet module,
Wifi Keypad or Cellular Radio
3) Register an installer account at
https://www.myalarm.com.au if you don't already
have one.
4) Take note of the 11 digit installer number (top right
of your screen or in your MyAlarm confirmation
email)
5) Enter installer panel programming mode on the
keypad
6) Select Menu 5-0-9
7) Enter the 11 digit installer number and press OK
8) Panel will take up to 1 minute to register
successfully to the MyAlarm servers
9) Login to https://www.myalarm.com.au and on the
home page you will see your newly registered
panel
7
10) Select the serial number of your panel and fill out
the site information
9
11) Select the prefered MyAlarm plan and confirm
payment.
S E R V I C E M O D E
Service mode when activated disables dialler reporting,
prevents all alarms and prevents all users from arming the
system.

Turning Service Mode ON

1) Enter programming mode.
[1][2][3][4] + [MENU]
2) Turn service mode on.
[MENU] [7][0][8]
3) Follow display prompts.
4) Hold down [MENU] to exit.
Keypads will display the word "SERVICE" in the middle
i
of the display when service mode is active.
Note

Turning Service Mode OFF

1) Enter programming mode.
[1][2][3][4] + [MENU]
2) Turn service mode on.
[MENU] [7][0][8]
3) Follow display prompts.
4) Hold down [MENU] to exit.
You must exit Service Mode to reactivate the system.
i
Service mode will automatically exit after 2 hours.
Note
Bosch Security Systems 10/22 BLCC615I