1. Manuals
  2. Brands
  3. Net to Net Technologies Manuals
  4. Multiplexer
  5. AIM24000
  6. User manual

Net to Net Technologies AIM24000 User Manual

Interface module 48-port adsl2+ inverse multiplexers
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Interface Module User Guide
AIM24000-48
and
AIM24000-48B
48-Port ADSL2+ Inverse Multiplexers
© Copyright 2004 Net to Net Technologies, Inc.
™ The Net to Net Logo is a trademark of Net to Net Technologies, Inc.
Worldwide Headquarters
http://www.nettonet.com
EMEA Headquarters
Net to Net Technologies
Net to Net Technologies
112 Corporate Drive
Victoria House, 19 Park Way
Portsmouth, NH 03801  USA
Newbury Berkshire RG14 1EE  UK
1 (877) 638-2638
44 (0) 1635-570950
support@nettonet.com
support-emea@nettonet.com
AIM24000 Installation 210-0000056 rev 01
Page 1 of 44

Advertisement

Table of Contents
loading

Related Manuals for Net to Net Technologies AIM24000

Summary of Contents for Net to Net Technologies AIM24000

  • Page 1 Net to Net Technologies Net to Net Technologies 112 Corporate Drive Victoria House, 19 Park Way Portsmouth, NH 03801  USA Newbury Berkshire RG14 1EE  UK 1 (877) 638-2638 44 (0) 1635-570950 support@nettonet.com support-emea@nettonet.com AIM24000 Installation 210-0000056 rev 01 Page 1 of 44...

  • Page 2: Table Of Contents

    2.2 Install the AIM24000 in an IP DSLAM 2.2.1 12-Slot IP DSLAM 2.2.1.1  Select a Slot for Installation 2.2.1.2  Align the AIM24000 with the Slot Module Guides 2.2.1.3  Slide the AIM24000 Firmly into the Chassis 2.2.1.4  Secure the AIM24000 in the Chassis 2.2.2 4-Slot IP DSLAM...

  • Page 3: Circuit Id

    5.2 DATA STORAGE 5.2.1 Memory 5.2.1.1  RAM 5.2.1.2  NVRAM 5.2.2 Local Files 5.2.2.1  Uploading a Port Template 5.2.2.2  Downloading a Port Template 5.3 Firmware Upgrades 5.4 Regulatory Compliance for Class A Equipment AIM24000 Installation 210-0000056 rev 01 Page 3 of 44...
  • Page 4 1.0 ADSL2+ INVERSE MULTIPLEXER MODEL TYPES 1.1 AIM24000-48 The AIM24000-48 is a 48-port ADSL2+ inverse multiplexer that supports Annex A (Plain Old Telephone Service-POTS) on lower end frequencies (up to 4 kHz). 1.2 AIM24000-48B The AIM24000-48B is a 48-port ADSL2+ inverse multiplexer that supports Annex B...

  • Page 5: Select

    OTE Although the AIM24000 can be installed in both the IPD12000 and the IPD12000E, the IPD12000 has the capability to support AIM24000 ports 1-24 only; in order to make use of all 48 ports, you must install the AIM24000 in an IPD12000E.
  • Page 6 DO NOT OPERATE YOUR IP DSLAM WITH AN EMPTY SLOT. 2.2.1.2 Align the AIM24000 with the Slot Module Guides With the AIM24000 Printed Circuit Board (PCB) facing RIGHT and the AIM24000 model name, and Net to Net logo, on the LOWER edge of the faceplate, align the upper and lower edges of the PCB with the slot module guides.
  • Page 7 OTE Although the AIM24000 can be installed in both the IPD4000 and the IPD4000E, the IPD4000 has the capability to support AIM24000 ports 1-24 only; in order to make use of all 48 ports, you must install the AIM24000 in an IPD4000E.
  • Page 8 OTE If you have not already powered up your IP DSLAM, do so now. Refer to your IP DSLAM Installation Instructions at http://www.nettonet.com/support/docs/#i POWER SPECIFICATIONS -48V DC (supplied by the host IP DSLAM) 1.6 Amps The PWR (power) LED on the AIM24000 faceplate will illuminate solid green to indicate the AIM24000 is receiving power. AIM24000 Installation 210-0000056 rev 01 AIM24000   ...
  • Page 9 (B) provides the ADSL connection for ports 25-48. OTE Net to Net's IPD12000 has only one female RJ21 connector for each interface module slot. These connectors support ports 1-24 (only) on your AIM24000; ports 25-48 cannot be connected in an IPD12000.
  • Page 10 2.4.1.1.2 Connect Your ADSL Cable(s) OTE No configuration is necessary for the AIM24000 to operate at default settings. However, if you wish to run your subscriber connections at settings other than the factory defaults, Net to Net recommends configuring the AIM24000 prior to ADSL connection. Refer to Section 4.0 for further information.
  • Page 11 IPD4000. 2.4.1.2.2 Connect Your ADSL Cable(s) OTE No configuration is necessary for the AIM24000 to operate at default settings. However, if you wish to run your subscriber connections at settings other than the factory defaults, Net to Net recommends configuring the AIM24000 prior to connection. Refer to Section 4.0 for further information.
  • Page 12 OTE If you are using a 120 or 180 degree cable, both the left and right sides of the RJ21 cable connector should be screwed to the connector frame on the chassis. AIM24000 Installation 210-0000056 rev 01                 MALE RJ21 CONNECTOR OF YOUR ADSL CABLE                ...
  • Page 13 2.4.2 Remote Connection A single line connection can be established between any port on the AIM24000 and any compatible G.lite, ADSL, ADSL2 or ADSL2+ modem. 2.4.3 ADSL RJ21 Pinout PORT RING TIP (Pins 25 and 50 are not used) 2.5 Verify the ADSL Connection(s) The LK (Link) LED for each port being connected to a remote modem will illuminate solid green to indicate a connection has been established.

  • Page 14: Default Configurations

    3.0 ADSL Parameters 3.1 Default Configurations No configuration is necessary for the AIM24000 to operate at default settings. PARAMETER Standard Mode Port Mode Upstream Speed Downstream Speed IP Range 1 IP Range 2-4 VLAN Backbone-VLAN VLAN Priority Protocol Flood Frame Type...

  • Page 15: Full Rate Adsl2

    ITU-T Recommendation G.992.3 in Annex L format. 3.2.2.3 Full Rate ADSL An AIM24000 port that is operating in full rate ADSL mode and utilizing a single line for both phone and data, requires an in-line splitter at both ends of the ADSL connection.

  • Page 16: G.lite

    Wire Gauge (AWG) cable; connections made with cable of a greater gauge (e.g., 24 AWG) will link up at greater distances. The AIM24000 may not link up if the cable is in poor condition or if the cable distance is greater than a particular bandwidth will support.
  • Page 17 11,000 12,000 13,000 14,000 15,000 16,000 17,000 18,000 19,000 3.2.4.1.2 G.DMT.BISplus (ADSL2+) An AIM24000 port in ADSL2+ mode is capable of reaching downstream speeds of up to 21,790 kbps under optimal circumstances. DISTANCE feet 8,000 9,000 10,000 11,000 12,000 13,000...

  • Page 18: Full Rate Adsl

    3.2.4.1.3 READSL2 (Reach Expanded ADSL2) DISTANCE feet 16,000 17,000 18,000 19,000 3.2.4.2 Full Rate ADSL An AIM24000 port in G.DMT, T1.413 or Alcatel mode is capable of reaching downstream speeds of up to 11,936 kbps under optimal circumstances. DISTANCE feet meters 8,000 2,438 9,000...

  • Page 19: Single Ip Address

    CLI or SNMP. 3.2.5.1 Single IP Address Starting IP Address = Ending IP Address An AIM24000 port configured with a single source IP address will only allow packets with that specific IP address to traverse the port. 3.2.5.2 IP Address Range Starting IP Address <...
  • Page 20 Traffic protocol is indicated by a 2-byte (hexidecimal) Ethertype code in packet headers. 3.2.9.1 All An AIM24000 port configured with Protocol All will allow packets with all Ethertype protocols to traverse the port. 3.2.9.2 Select An AIM24000 port configured with Protocol Select allows specification of up to four [4] Ethertype protocols;...
  • Page 21 Virtual Path as identified by a Virtual Channel Identifier (VCI) and a Virtual Path Identifier (VPI). A VPI is designated by an 8-bit field in ATM cell headers and a VCI is designated by a 16-bit field in ATM cell headers. The AIM24000 supports one PVC per port.
  • Page 22 BEFORE the VPI and VCI values are entered. When manually configuring VPI and VCI, each port on the AIM24000 must be assigned the same VPI and VCI values as the remote ADSL modem to which that port is connected in order for the units to communicate.
  • Page 23 AIM24000 Installation 210-0000056 rev 01 Page 23 of 44...
  • Page 24 Device Type should specify AIM24000-48 or AIM24000- 48B and the Revision should list the firmware version of the AIM24000. If you wish to configure a different port from that which is listed, use the Slot and Port pull-down menus to specify another port location.
  • Page 25 Enter the desired upstream (Up) and downstream (Dn) rates (kbps) in the corresponding fields. 4.1.2.3.2 Fixed Adaptive Enter the desired maximum boundaries, for both upstream (Up) and downstream (Dn) rates (kbps), in the corresponding fields. AIM24000 Installation 210-0000056 rev 01 Page 25 of 44...
  • Page 26 4.1.2.4.1 Manual Configuration VPI value range: 0 - 7 VCI value range: 0 - 255 If you wish to manually configure VPI and VCI values, you must first set VPI/VCI Detect to Off. AIM24000 Installation 210-0000056 rev 01 Page 26 of 44...
  • Page 27       4.1.2.5 IP Range Proper Syntax: xxx.xxx.xxx.xxx Value Range: 0-255 for each triple-digit quadrant Default: 0.0.0.0 - 255.255.255.255 Enter IP Range start and end parameters in the appropriate fields. AIM24000 Installation 210-0000056 rev 01 Page 27 of 44...
  • Page 28 4.1.2.5.3 Full IP Address Range (default) Starting IP = 0.0.0.0 Ending IP = 255.255.255.255 4.1.2.6 Protocol Options: All or Select Default: All Click to fill the circle for either All or Select. AIM24000 Installation 210-0000056 rev 01 Page 28 of 44...
  • Page 29 Configuring AIM24000 port protocol as Select requires specification of desired Ethertypes (up to four [4]). OTE Not all IP DSLAM management modules provide the Protocol Select option in NMS. In these instances, you will be required to select between All or IP, where IP indicates that only Transmission Control Protocol (TCP), Internet Protocol (IP), and Address Resolution Protocol (ARP) traffic will be allowed to traverse the port.
  • Page 30 Click the box to activate Layer 2 Port Filters, then specify up to three [3] MAC addresses. Packets containing a MAC Address that has been specified as a Layer 2 Filter for an AIM24000 port will not be allowed to enter any AIM24000 Installation 210-0000056 rev 01...
  • Page 31 OTE If you have chosen to allow an unlimited number of MAC addresses, it is unnecessary to also configure static MAC addresses (Section 4.1.2.8.1) UNLESS you wish to tie those specific MAC addresses to the AIM24000 port such that no OTHER ports on the IP DSLAM will be allowed to receive packets containing said MAC addresses.
  • Page 32 Use the pull-down menu to select either 1483LLC or 1483VCM. 4.1.2.10 Standard Mode Options: Multimode, T1.413, G.lite, G.DMT, Alcatel, G.DMT.BIS, G.DMT.BISplus                or READSL2 Default: Multimode Use the pull-down menu to select the desired mode. AIM24000 Installation 210-0000056 rev 01 Page 32 of 44...
  • Page 33 4.1.2.11 Submit Click the submit button at the bottom of the Circuit Configuration window. AIM24000 Installation 210-0000056 rev 01 Page 33 of 44...
  • Page 34 Terminal Emulator program. OTE AIM24000 Ports 25-48 cannot currently be managed via CLI; only Ports 1-24 can be managed via CLI at present. If your IP DSLAM is newly installed and has not yet been initialized, you must configure the IP Address, Subnet Mask and Gateway via a direct PC to DSLAM connection before you will be able to access data or complete any other configurations.
  • Page 35 Launch a Terminal Emulator program on your PC. The following information will appear on your Terminal Emulator screen, followed by a request for username. You must log in as a Superuser in order to configure an AIM24000 port. Net to Net Technologies [IP DSLAM model name]...
  • Page 36 Downstream = xxxx (kbps) Upstream = yyyy (kbps) Default: n/a (Adaptive Port Mode) [system name] ->SET SLOT [slot number of the AIM24000] PORT [ALL or port number] SPEED [xxxx] [yyyy] Example: [system name] ->set slot 2 port 10 speed 1024 8064 4.2.2.5 IP Range...
  • Page 37 IEEE 802.1Q VLAN Access Port; only packets with the specified VLAN tag will be allowed to traverse the port. [system name] ->SET SLOT [slot number of the AIM24000] PORT [ALL or port number] VLAN_RANGE [1-10] [(1-4085)-(1-4085)] Example: [system name] ->set slot 2 port 10 vlan_range 1 100-100...
  • Page 38 INGRESS PACKETS FROM WITH uplink 4.2.2.7 Backbone-VLAN Value Range: 0 - 4085 Default: 0 (off) [system name] ->SET SLOT [slot number of the AIM24000] PORT [ALL or port number] BACKBONE_VLAN [0-4085] Example: [system name] ->set slot 2 port 10 backbone_vlan 100 INGRESS PACKETS...
  • Page 39 VLAN Range 4.2.2.9 Protocol Options: ALL or IP Default: ALL [system name] ->SET SLOT [slot number of the AIM24000] PORT [ALL or port number] Protocol [All or IP] Example: [system name] ->set slot 2 port 10 protocol all 4.2.2.10 Flood...
  • Page 40 MIB browser user manual for compilation and usage instructions. OTE AIM24000 Ports 25-48 cannot currently be managed via CLI; only Ports 1-24 can be managed via CLI at present. If your IP DSLAM is newly installed and has not yet been initialized, you must configure the IP Address, Subnet Mask and Gateway via either NMS or CLI before you will be able to utilize SNMP.
  • Page 41 VLAN END TAG ifCfgVlanIdEnd ADSL SLOT INDEX ifCfgAdslSlotIndex ADSL PORT INDEX ifCfgAdslPortIndex PORT MODE ifCfgAdslPortMode VPI/VCI DETECT ifCfgAdslVpiVciDetect RX RATE ifCfgAdslRxRate AIM24000 Installation 210-0000056 rev 01 OID (1.3.6.1.4.1.8059. INPUT/RETURN VALUES 1.2.1.1.1.2.1.1.5.x.y User Defined 1.2.1.1.1.2.1.1.6.x.y User Defined 1.2.1.1.1.2.1.1.7.x.y User Defined 1.2.1.1.1.2.1.1.8.x.y 0-4085 1.2.1.1.1.2.1.1.9.x.y...

  • Page 42: Led Indications

    5.2 DATA STORAGE Configuration backup is inherent in the AIM24000. Upon initial power up of the host IP DSLAM, default parameters of the AIM24000 will remain in place unless changed through NMS, CLI or SNMP. AIM24000 Installation 210-0000056 rev 01 OID (1.3.6.1.4.1.8059.
  • Page 43 (NVRAM) of the IP DSLAM's management module. 5.2.1.1 RAM Statistical data stored only in AIM24000 RAM, such as traffic statistics and link up/down time, will be erased if the module is removed from the IP DSLAM or the IP DSLAM loses power.
  • Page 44 Refer to Net to Net's Firmware Upgrade Procedure at http://www.nettonet.com/support/docs/230-0000032 5.4 Regulatory Compliance for Class A Equipment OTE The following regulatory information applies to the AIM24000 as installed in a Net to Net IP DSLAM. NEBS: GR-63-CORE, GR-1089-CORE EMC: FCC Part 15; CSA/C108.8; EN55022, EN55024 SAFETY: UL 60950-1 1st Edition, UL Marking;...

This manual is also suitable for:

Aim24000-48Aim24000-48bAim24000-48

Table of Contents