1. Manuals
  2. Brands
  3. Net to Net Technologies Manuals
  4. Multiplexer
  5. 12-Port T1 Access Multiplexer TAM1500-12
  6. User manual

Net to Net Technologies 12-Port T1 Access Multiplexer TAM1500-12 User Manual

Paradyne 12-port t1 access multiplexer user's guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
CAUTION
Net to Net Technologies strongly recommends the use of proper electrostatic discharge (ESD) precautions
when handling this equipment.
INSTALLATION
1. Unpack and inspect the TAM1500-12.
If there is visible damage, do not attempt to connect the device; contact Customer Support at 1-
877-638-2638 (001-603-427-0600 for international customers) or Support@NetToNet.com.
2. Install the TAM1500-12 in an IP DSLAM chassis.
NOTE
There must be a Multiplexer Uplink Module installed in the IP DSLAM chassis in order for Access Modules to
operate.
All Access Multiplexer Modules for Net to Net Technologies' IP DSLAMs are hot swappable;
installing or removing an Access Module while the chassis is powered up does not affect the
operational status of other Access Modules within the chassis. The IPD12000 is a fourteen slot
chassis; slots 1-12 are reserved for Access Modules (such as the TAM1500-12) and slots 13-14
are reserved for Multiplexer Uplink Modules (such as the MUM200-2). Access Modules may be
placed in any order in slots 1-12. The IPD4000 is a five slot chassis; slots 1-4 are reserved for
Access Modules and slot 5 is reserved for a Multiplexer Uplink Module.
a. Align the TAM1500-12 with the slot module guides of the chosen slot for installation (slot
1-12 on the IPD12000 or slot 1-4 on the IPD4000).
b. Slide the TAM1500-12 firmly into the chassis. DO NOT USE EXCESS FORCE.
c. Secure the TAM1500-12 by tightening the fastening screws on the module faceplate.
d. Verify that the PWR (Power) LED on the TAM1500-12 faceplate is illuminated.
210-0000025 rev04
TAM1500-12
12-Port T1 Access Multiplexer
Interface Module User Guide

Advertisement

Table of Contents
loading

Related Manuals for Net to Net Technologies 12-Port T1 Access Multiplexer TAM1500-12

Summary of Contents for Net to Net Technologies 12-Port T1 Access Multiplexer TAM1500-12

  • Page 1 CAUTION Net to Net Technologies strongly recommends the use of proper electrostatic discharge (ESD) precautions when handling this equipment. INSTALLATION 1. Unpack and inspect the TAM1500-12. If there is visible damage, do not attempt to connect the device; contact Customer Support at 1- 877-638-2638 (001-603-427-0600 for international customers) or Support@NetToNet.com.

  • Page 2: Connect The T1 Line(S)

    3. Connect the T1 Line(s). Plug the T1 cable into the RJ21 connector for the chosen slot on the back of the IP DSLAM. The TAM1500-12 will connect with remote T1 modems at distances up to 6,000 feet before requiring a T1 repeater. For each port being connected to a remote T1 modem, verify that the T1 link has been established;...

  • Page 3: Default Settings

    192.168.254.252 if the MUM is in slot 13 (IPD12000) or slot 5 (IPD4000) 192.168.254.253 if the MUM is in slot 14 (IPD12000) e. Log in with a default username and password (both of which are case sensitive). Please note that General Users have "read only" access; for NMS configuration you must log in as a Superuser.

  • Page 4: Data Storage

    Management System Configuration Defaults IP Addresses: IPD12000 slot 13 192.168.254.252 IPD12000 slot 14 192.168.254.253 IPD4000 slot 5 192.168.254.252 TAM1500-12 Circuit Defaults Circ. ID: IP Range 1: 0.0.0.0 - 255.255.255.255 IP Range 2: 0.0.0.0 - 0.0.0.0 Speed: 1,536 kbps Protocol: Backbone-VLAN: 0 VLAN: 0 - 0 Data Storage...

  • Page 5: Frame Type

    NOTE Although all 24 channels continually run at 1,536 kbps, the Timeslot configuration for each port determines how many of the channels will be receiving data for that port. Ports configured to operate as fractional T1 lines require contiguous timeslots, as indicated in the table above. Frame Type Frame type is the T1 data encapsulation method.

  • Page 6: Additional Information

    0db (Default) Receivers on most newer T1 equipment (repeaters, switches, etc.) can automatically adjust for incoming amplitude, allowing them to run at zero attenuation regardless of distance. -7.5db, -15db or -22db Some older T1 equipment (repeaters, switches, etc.) cannot automatically adjust for incoming amplitude, in which case, it may be necessary to set attenuation manually (through NMS) from the choices above.

  • Page 7: Regulatory Compliance

    T1 TX flashing (Transmitting) amber solid amber illumination T1 AL (Alarm) illumination solid amber pulsing amber (A pulsing LED blinks steadily at a rate of once per second. A flashing LED blinks at a more rapid, less constant rate.) Regulatory Compliance FCC Regulatory Compliance Information for Class A Equipment Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
  • Page 8 Caution: This unit does not contain any user serviceable parts. Repair service and/or warranty information may be obtained by contacting Customer Support at Net to Net Technologies, Inc.: 112 Corporate Drive, Suite 1, Portsmouth, NH 03801 (603) 427-0600 / (877) 638-2638, Contact@NetToNet.com / www.nettonet.com Industry Canada Regulatory Compliance Information for Class A Equipment This Class A digital apparatus complies with Canadian ICES-003.

This manual is also suitable for:

Tam1500

Table of Contents