Advertisement
Quick Links
CAUTION
Net to Net Technologies strongly recommends the use of proper electrostatic discharge (ESD) precautions
when handling this equipment.
INSTALLATION
1. Unpack and inspect the SAM1000-12.
If there is visible damage, do not attempt to connect the device; contact Customer Support at 1-
877-638-2638 (1-603-427-0600 for international customers) or Support@NetToNet.com.
2. Install the SAM1000-12 in an IP DSLAM chassis.
NOTE
There must be a Multiplexer Uplink Module installed in the IP DSLAM chassis in order for Access Modules to
operate.
All Access Multiplexer Modules for Net to Net Technologies' IP DSLAMs are hot swappable;
installing or removing an Access Module while the chassis is powered up does not affect the
operational status of other Access Modules within the chassis. The IPD12000 is a fourteen slot
chassis; slots 1-12 are reserved for Access Modules (such as the SAM1000-12) and slots 13-14
are reserved for Multiplexer Uplink Modules (such as the MUM200-2). Access Modules may be
placed in any order in slots 1-12. The IPD4000 is a five slot chassis; slots 1-4 are reserved for
Access Modules and slot 5 is reserved for a Multiplexer Uplink Module.
a. Align the SAM1000-12 with the slot module guides of the chosen slot for installation (slot
1-12 on the IPD12000 or slot 1-4 on the IPD4000).
b. Slide the SAM1000-12 firmly into the chassis. DO NOT USE EXCESS FORCE.
c. Secure the SAM1000-12 by tightening the fastening screws on the module faceplate.
d. Verify that the PWR (Power) LED on the SAM1000-12 faceplate is illuminated.
210-0000011 rev03
SAM1000-12
12-Port SDSL Access Multiplexer
Interface Module User Guide
Advertisement
Related Manuals for Net to Net Technologies SAM1000
Summary of Contents for Net to Net Technologies SAM1000
- Page 1 1-12. The IPD4000 is a five slot chassis; slots 1-4 are reserved for Access Modules and slot 5 is reserved for a Multiplexer Uplink Module. a. Align the SAM1000-12 with the slot module guides of the chosen slot for installation (slot 1-12 on the IPD12000 or slot 1-4 on the IPD4000).
- Page 2 SDSL Ring 1 NOTE Once the SAM1000-12 has been installed, bandwidth and other configurations are software selectable via Net to Net Technologies' Network Management System (NMS). For further information regarding SAM1000-12 configuration and management please refer to the Management User Guide for IP and Mini DSLAMs.
-
Page 3: Default Settings
Information Technology Manager. Default Settings No configuration is necessary for the SAM1000-12 to operate at default settings. If however, a change is required, default settings can easily be modified within NMS. For information regarding specific parameter configurations, refer to the Management User Guide for IP and Mini DSLAMs. -
Page 4: Circuit Configuration
Memory (RAM) of the SAM1000-12 and the Non-Volatile Random Access Memory (NVRAM) of the MUM. While data stored in SAM1000-12 RAM will be erased if the unit loses power, data stored within MUM NVRAM will remain intact (even if the unit loses power) unless deliberately cleared or reconfigured. -
Page 5: Led Indicators
Additional Information unit is operational If the Power LED is not illuminated, it is unlikely the SAM1000-12 is receiving power and none of the LEDs will be illuminated. SDSL connection is The SDSL link is operational and traffic is flowing. - Page 6 cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Caution: Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.