TransAct Ithaca 8000 Programmer's Manual page 317

Index
OCR Characters, Enabling, 95
OFF Button, 39
Off-line active, 289
One Line/Double Wide Print, Beginning, 98
One Line/Double Wide Print, Canceling, 98
Output Paper end Signals, Selecting Paper Sensors,
162, 201
Panel Button Commands, 199
paper Feed, Enable, Disable, 161, 199
Paper Feed, Enable/Disable, 234
Paper Low Sensor, 234
Paper Motion, 73
Paper Out Sensor, disable, 158
Paper Out Sensor, enabling, 158
Paper Out Status, Inquire, 170
Paper Sensor Commands, 200
Paper Sensors, Selecting to Stop Printing, 162, 200
Parallel Interface Connector, 33
Parallel port timing, 274
PcOS Control Codes, 59
PcOS Quick Reference Chart, 60
Peripheral Devise Status, Selecting, 224
Plug and Play
parallel, 277
Serial, 283
Power Control, Remote, 166, 286
Power Cycle Status, Inquire, 171
Power-cycle recovery, 288
Print
rotation, 104
Print and Carriage Return, 188
Print and Feed Lines, 188
Print and Feed Paper, 189
Print and Line Feed, 188
Print and Reverse Feed Lines, 188, 189
Print Buffer Flow, 281
Print Buffer Size, 283
Print buffer, control, 159
Print buffers, 269
Print counter, 226
Print Current Configuration, 264
Print Current totals, 264
Print margins, setting, 158
Print Modes, Selecting, 196
Print Position Commands, 202
Print Quality Mode, Setting, 87
Print Style, Setting, 100
Print Supress/Data Pass Through, Enabling, 163
Printer Care, 39
Printer ID, Inquire, 174
Printer Reset, Requesting, 170
Printer State, Inquire, 172
Printer Status, 168
Printer Status, Inquire, 169, 173
Process User Macro, 129
Programmer's Notes, 291
Programming Considerations, 128
Quad Density Graphics, Printing, 115
Query marker, 159
Read and return Totals, 261
Real Time Status, Transmitting, 210
real-time Request to Printer, 225
100-06908
®
Ithaca
Recovery form Mechanical Errors, 290
Regulatory Compliance, ii
Remote Power Control, 166, 286
Remote Reset, 287
Removing Old Interface Cards, 30, 31
Rotated Font, Beginning, 88
Rotated Print, 270 , 107
Rotated Print, 270 with 2 Pass Font, 108
Rotated Print, 270 with 2 Pass Font and line
formatting, 108
Rotated Print, 270 with Line Formatting, 107
Rotated Print, 90 , 107
Rotated Print, 90 with 2 Pass Font and Line
Formatting, 107
Rotated Print, 90 with Line Formatting, 107
Rotated Print, Begin 90 with 2 pass font, 107
Rotated Print, Beginning, 105
Rotated Print, Ending, 108
Rotated Print, Line Length, 109
Rotated Print, Line Spacing, 109
Select Character Font Table, 191
Select Color, 98
Select Subscript, 102
Select Superscript, 102
Self-Test
Using, 42
Serial Device Identification, 284
Serial Interface Communication, 24
Serial Interface Connector, 33
Serial port
flow control, 279
Serial Port
Inquire, 285
Signal Levels, 23
Single Density Graphics, Printing, 114
Specifications and Requirements, 11
Standard APA Graphics, 114
Standard Emulation, 58
Start up Macro, Flagging, 122
Status Commands, 207
Status Inquire, 168
Status, Inquire Receipt Paper Low, 169
Superscript and Subscript, 102
Tab Stops, Resetting, 75, 79
Testing the Printer, 42
TM T90 and EPOS Command Descriptions, 188
TM-90
Command Summary, 180
Top of Form, Setting, 80
Transmit Printer ID, 222
Transmit Status, 209
Transmits maintenance counter, 227
Turns smoothing on/off, 198
Underline Mode, On/Off, 196
Underline, Beginning, 99, 101
Unicode, 255
Unidirectional Printing, Beginning, 116
Upside down Print Mode, On/Off, 197
USB Interface Connector, 34
User Defined Character Set, Selecting, 190
User Defined Character, Saving, 122, 124
User Defined Characters, Canceling, 95, 191
Rev D
8000 Programmer's Guide
Page 303