Electrical Data, 525-600 - Danfoss VLT FC 102 Operating Manual

VLT HVAC Drive FC 102
Operating Guide
Type designation
Power losses and efficiency
Estimated power loss at rated maximum load [W]
Efficiency
(3)
B3+4 and C3+4 may be converted to IP21 using a conversion kit.
1
The typical power loss is at normal load conditions and expected to be within ±15% (tolerance relates to variety in voltage and cable conditions).
2
Values are based on a typical motor efficiency. Lower efficiency motors also add to the power loss in the drive and vice versa. If the switching fre-
quency is raised from nominal, the power losses may rise significantly. LCP and typical control card power consumptions are included. Further op-
tions and customer load may add up to 30 W to the losses. (Though typically only 4 W extra for a fully-loaded control card or options for slot A or slot
B, each). Although measurements are made with state-of-the-art equipment, some measurement inaccuracy must be allowed for (±5%).
Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency.
3
8.3 Electrical Data, 525–600 V
Table 49: Mains Supply 3x525–600 V AC - Normal Overload 110% for 1 Minute, P1K1–P7K5
Type designation
Typical shaft output [kW]
IP20/UL Open Type
IP21/UL Type 1
IP55/UL Type 12
IP66/UL Type 4X
Output current
Continuous (3x525–550 V) [A]
Intermittent (3x525–550 V) [A]
Continuous (3x525–600 V) [A]
Intermittent (3x525–600 V) [A]
Continuous kVA (525 V AC) [kVA]
Continuous kVA (575 V AC) [kVA]
Maximum input current
Continuous (3x525–600 V) [A]
Intermittent (3x525–600 V) [A]
SCCR
A2/A3 with mains disconnect [kA
A4/A5 with mains disconnect [kA
Without mains disconnect [kA
90 | Danfoss A/S © 2023.09
(2)
P1K1
1.1
A3
A3
A5
A5
2.6
2.9
2.4
2.6
2.5
2.4
2.4
2.7
] 50 kA
rms
] 65 kA
rms
] 100 kA
rms
P37K P45K
739 843
0.98 0.98
P1K5 P2K2 P3K0
1.5 2.2 3.0
A3 A3 A3
A3 A3 A3
A5 A5 A5
A5 A5 A5
2.9 4.1 5.2
3.2 4.5 5.7
2.7 3.9 4.9
3.0 4.3 5.4
2.8 3.9 5.0
2.7 3.9 4.9
2.7 4.1 5.2
3.0 4.5 5.7
50 kA 50 kA 50 kA
65 kA 65 kA 65 kA
100 kA 100 kA 100 kA
Specifications
P55K P75K P90K
1083 1384
0.98 0.98
P3K7 P4K0 P5K5
3.7 4.0 5.5
A2 A3 A3
A2 A3 A3
A5 A5 A5
A5 A5 A5
– 6.4 9.5
– 7.0 10.5
– 6.1 9.0
– 6.7 9.9
– 6.1 9.0
– 6.1 9.0
– 5.8 8.6
– 6.4 9.5
50 kA 50 kA 50 kA
65 kA 65 kA 65 kA
100 kA 100 kA 100 kA
AQ267037536117en-000101 / 130R0083
1474
0.99
P7K5
7.5
A3
A3
A5
A5
11.5
12.7
11
12.1
11
11
10.4
11.5
50 kA
65 kA
100 kA