Appendix 2 List Of Parameters Classified By Purposes Of Use - Mitsubishi Electric FR-A520-2.2K Instruction Manual

Appendix 2 List of Parameters Classified by Purposes of Use

Appendix 2 List of Parameters Classified by Purposes of Use
Set the parameters according to the operating conditions. The following list indicates purposes of use and
parameters. (For full information on the parameters, Refer to Chapter 4.)
Purpose of Use
Adjustment of acceleration/deceleration time and
pattern
Motor overheat protection
Selection of optimum output characteristic for load
characteristic
Limit of output frequency
Operation over 60Hz
Adjustment of frequency setting signal and output
Calibration of frequency meter
Adjustment of digital frequency meter
Adjustment of motor output torque
Multi-speed operation
Jog operation
Frequency jump operation
Reversible operation according to analog signal polarity
Automatic restart after instantaneous power failure
Adjustment of brake operation
Timing of magnetic brake operation
Display of speed, etc.
Function rewrite prevention
Reverse rotation prevention
Optimum acceleration/deceleration within continuous
rating range
Energy-saving operation
Automatic restart after alarm stop
Sub-motor operation
To make desired output characteristics (V/F pattern)
Operation via communication with personal computer
Operation under PID control
To perform commercial power supply-inverter switch-
over operation
To make backlash compensation
To detect current
Assignment of input terminal functions
Assignment of output terminal functions
To suppress noise
To group parameters
To set initial values for parameters
Clearing of inverter's actual operation time
High-speed frequency control operation
To exercise stop-on-contact control
To increase cooling fan life
To decelerate inverter to a stop at power failure
Advanced magnetic flux vector control operation
Programmed operation
Selection of key beep
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Parameter Numbers
Parameter numbers which must be set
Pr. 7, Pr. 8, Pr. 20, Pr. 21
Pr. 9
Pr. 3
Pr. 1, Pr. 2, Pr. 18
Pr. 903, Pr. 905
Pr. 73, Pr. 902, Pr. 903, Pr. 904, Pr. 905
Pr. 54, Pr. 55, Pr. 56, Pr. 158, Pr. 900
Pr. 54, Pr. 55, Pr. 56, Pr. 900
Pr. 0, Pr. 80, Pr. 81
Pr. 4, Pr. 5, Pr. 6, Pr. 24, Pr. 25, Pr. 26, Pr. 27, Pr. 232,
Pr. 234, Pr. 235, Pr. 236, Pr. 237, Pr. 238, Pr. 239
Pr. 15, Pr. 16
Pr. 31, Pr. 32, Pr. 33, Pr. 34, Pr. 35, Pr. 36
Pr. 28, Pr. 73
Pr. 57, Pr. 58
Pr. 10, Pr. 11, Pr. 12
Pr. 42,
Pr. 37, Pr. 52, Pr. 53
Pr. 77
Pr. 78
Pr. 60
Pr. 60
Pr. 65, Pr. 67, Pr. 68, Pr. 69
Pr. 0, Pr. 3, Pr. 7, Pr. 8, Pr. 44, Pr. 45, Pr. 46, Pr. 47, Pr.
110, Pr. 111, Pr. 112, Pr. 113
Pr. 100 to Pr. 109
Pr. 117 to Pr. 124
Pr. 128 to Pr. 134
Pr. 135 to Pr. 139
Pr. 140 to Pr. 143
Pr. 150 to Pr. 153
Pr. 180 to Pr. 186
Pr. 190 to Pr. 195
Pr. 72, Pr. 240
Pr. 160, Pr. 173 to Pr. 176
Pr. 199
Pr. 171
Pr. 271 to Pr. 274
Pr. 275, Pr. 276
Pr. 244
Pr. 261 to Pr. 266
Pr. 80, Pr. 81
Pr. 200 to Pr. 231
Pr. 990
207
APPENDICES