Parameter List; List Of Parameters Classified By The Purpose - Mitsubishi Electric FR-F720P-0.75K Instruction Manual

Fr-f700p series
Hide thumbs Also See for FR-F720P-0.75K:
Table of Contents

Advertisement

5.10 Parameter list

5.10.1 List of parameters classified by the purpose

Set the parameters according to the operating conditions.
The following list indicates purpose of use and corresponding parameters.
Purpose of Use
Acceleration/deceleration time/pattern adjustment
Acceleration/deceleration time/pattern adjustment
Acceleration/deceleration time/pattern adjustment
Acceleration/deceleration time/pattern adjustment
Adjusting the output torque (current) of the motor
Adjusting the output torque (current) of the motor
Adjusting the output torque (current) of the motor
Adjusting the output torque (current) of the motor
Adjusting the output torque (current) of the motor
Communication operation and command source
Communication operation and command source
Communication operation and setting
Communication operation and setting
Communication operation and setting
Communication operation and setting
Detection of output frequency and current
Detection of output frequency and current
Energy saving operation
Frequency setting by analog input
Frequency setting by analog input
Frequency setting by analog input
Frequency setting with terminals (contact input)
Frequency setting with terminals (contact input)
Frequency setting with terminals (contact input)
Function (Parameter Number)
— Acceleration/deceleration patterns and backlash measures (Pr.29, Pr.140 to
Pr.143)
— Acceleration/deceleration time setting (Pr.7, Pr.8, Pr.20, Pr.21, Pr.44, Pr.45,
Pr.147, Pr.791, Pr.792)
— Regenerative avoidance operation (Pr.665, Pr.882 to Pr.886)
— Starting frequency (Pr.13, Pr.571)
— Manual torque boost (Pr.0, Pr.46)
— Simple magnetic flux vector control (Pr.90)
— Simple magnetic flux vector control and IPM motor control (Pr.80)
— Slip compensation (Pr.245 to Pr.247)
— Stall prevention (Pr.22, Pr.23, Pr.48, Pr.49, Pr.66, Pr.148, Pr.149, Pr.154,
Pr.156, Pr.157)
— Selection of the NET operation mode command source (Pr.550)
— Selection of the PU operation mode command source (Pr.551)
— Control of parameter write by communication (Pr.342)
— Control of parameter write by communication (Pr.342)
— Initial setting of RS-485 communication
(Pr.117 to Pr.124, Pr.551)
— Initial setting of RS-485 communication (Pr.331 to Pr.343, Pr.502, Pr.539,
Pr.549 to Pr.551, Pr.779)
— Detection of output current (Y12 signal) and zero current (Y13 signal) (Pr.150
to Pr.153, Pr.166, Pr.167)
— Detection of output frequency (SU, FU, and FU2 signals)
(Pr.41 to Pr.43, Pr.50, Pr.870)
— Energy saving control selection (Pr.60)
— Analog input selection, override function, analog input compensation (Pr.73,
Pr.242, Pr.243, Pr.252, Pr.253, Pr.267)
— Bias and gain for the frequency setting voltage (current) (Pr.125, Pr.126,
Pr.241, C2(Pr.902) to C7(Pr.905))
— Noise elimination at the analog input (Pr.74)
— Compensation of multi speed and remote setting inputs (Pr.28)
— Jog operation (Pr.15, Pr.16)
— Multi-speed setting operation
(Pr.4 to Pr.6, Pr.24 to Pr.27, Pr.232 to Pr.239)
Parameter list
Page
91
88
112
89
87
98
98
106
90
108
108
108
99
99
108
103
5
92
95
96
100
97
90
89
87
83

Advertisement

Table of Contents
loading

Table of Contents