005 Nl Equalizer; 006 Telephone Line Monitor; 007 Att Transmission Level; 008 V.34 Modulation Speed Upper Limit - Canon ImageRUNNER 1022iF Service Manual

15.4.2 <No.005 NL equalizer>
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Use it to enable-disable the NL equalizer.
If errors occur often during communication because of the condition of the line, enable (ON) the NL equalizer.
Any of the following error codes may be indicated at time of transmission because of the line condition:
##100, ##101, ##102, ##104, ##201, ##281, ##282, ##283, ##750, ##755, ##765, ##774, ##779, ##784, ##789
Any of the following error codes may be indicated at time of transmission because of the line condition:
##103, ##107, ##114, ##201, ##790, ##793
15.4.3 <No.006 telephone line monitor>
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Use it to s the telephone line monitor function:
DIAL: generate the monitor sound of the telephone line using the speaker from the start of transmission to DIS.
SERVICEMAN [1]: generate the monitor sound of the telephone line using the speaker from the start of communication to the end of it.
SERVICEMAN [2]: generate the monitor sound of the telephone line2 (Option).
OFF: do not generate the monitor sound of the telephone line using the speaker.
15.4.4 <No.007 ATT transmission level>
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Use it to set the transmission level (ATT).
Raise the transmission level if errors occur frequently at time of communication because of the condition of the line. (It means close to 8)
Any of the following error codes may be indicated at time of transmission because of the line condition:
##100, ##101, ##102, ##104, ##201, ##280, ##281, ##282, ##283, ##284, ##750, ##752, ##754, ##755, ##757, ##759, ##760, ##762, ##764, ##765,
##767, ##769, ##770, ##772, ##774, ##775, ##777, ##779, ##780, ##782, ##784, ##785, ##787, ##789
Any of the following error codes may be indicated at time of reception because of the line condition:
##103, ##106, ##107, ##201, ##793
15.4.5 <No.008 V.34 modulation speed upper limit>
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Use it to set an upper limit to the modulation speed (baud rate) for the V.34 primary channel.
15.4.6 <No.009 V.34 data speed upper limit>
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Use it to set an upper limit to the data transmission speed for the V.34 primary channel between 2.4K and 33.6K bps in increments of 2400 bps. (0: 2.4K to 13:
33.6K bps).
15.4.7 <No.010 Frequency of the pseudo CI signal>
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
You may select a frequency for the pseudo CI signal.
Some types of external telephones do not ring when the fax/tel switch-over function is ON. To sound the ring, change the pseudo CI signal.

15.5 Setting of Numeric Parameter (NUMERIC Param.)

15.5.1 Numerical Parameter Composition

/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
No.
002
003
004
005
006
010
011
013
015
016
017
018
019
020
021
022
Item
RTN transmission condition(1)
RTN transmission condition (2)
RTN transmission condition (3)
NCC pause time length (pre-ID code)
NCC pause time length (post-ID code)
line condition identification time length
T.30T1 timer (for reception)
T.30 EOL timer
hooking detection time length
time length to first response at time of fax/tel switchover
pseudo RBT signal pattern ON time length
pseudo RBT signal pattern OFF time length
(short)
pseudo RBT signal pattern OFF time length
(long)
pseudo CI signal pattern ON time length
pseudo CI signal pattern OFF time length
(short)
pseudo CI signal pattern OFF time length (long)
T-15-15
Range of settings
1% to 99%
2 to 99 item
1 to 99 lines
1 to 60 sec
1 to 60 sec
0 to 9999 (10 msec)
0 to 9999 (10 msec)
500 to 3000 (10 msec)
0 to 999
0 to 9
0 to 999
0 to 999
0 to 999
0 to 999
0 to 999
0 to 999
Chapter 15
0013-1334
0013-1335
0013-1336
0013-1337
0013-1338
0013-1339
0013-1340
15-13