Table of Contents
Advertisement
Chapter 15
15.3.10 SSSW-SW30
15.3.10.1 List of Functions
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Bit
0
1
2
3
4
5
6
7
15.3.10.2 Detailed Discussions of Bit 5
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
When "Detect with the new method" is selected, tone is detected for 3.5 seconds before call origination in order to discriminate between dial tone and voice. If dial
tone is detected and the time since line seizure is 3.5 seconds or longer, call origination takes place immediately. If the time since line seizure is less than 3.5 seconds,
call origination takes place after waiting for 1 second. (If the time since line seizure reaches 3.5 seconds during the 1-second waiting period, call origination takes
place immediately. By default, "Detect with a new method" is assigned for this SW.
15.3.11 SSSW-SW34
15.3.11.1 List of Functions
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Bit
0
1
2
3
4
5
6
7
15.3.11.2 Detailed Discussions of Bit 0
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
You can select whether a waste toner full warning is to be displayed.
When "1" is selected, a waste toner full warning is displayed.
When "0" is selected, a waste toner full warning is not displayed.
15.3.11.3 Detailed Discussions of Bit 1
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Select whether to display the waste toner full warning as a drum replacement required message or as E019 displayed on an operator call. Select 1 to display a rum
replacement required message on an operator call. Select 0 to display E019 on an service call.
15.4 Setting of Menu Switch (Menu)
15.4.1 Menu Switch Composition
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
No.
005
006
007
008
009
010
15-12
Function
Not used
Not used
Not used
Not used
Not used
New dial tone detection method
Not used
Not used
Function
Display the waste toner full
warning
Switch the waste toner full
warning
Not used
Not used
Not used
Not used
Not used
Not used
Function
Range of settings
NL equalizer
1: ON, 0: OFF
telephone line monitor
0:DIAL, 1:SERVICEMAN1, 2:SERVICEMAN2, 3:OFF
transmission level (ATT)
from 0 to 15 (ex: 15= -15 dBm)
V.34 modulation speed upper
0:3429, 1:3200, 2:3000, 3:2800, 4:2743, 5:2400
limit
V34 data speed upper limit
0:33.6 kbps, 1:31.2 kbps, 2:28.8 kbps, 3:26.4 kbps, 4:24.0 kbps,
5:21.6 kbps, 6:19.2 kbps, 7:16.8 kbps, 8:14.4 kbps, 9:12.0 kbps,
10:9.6 kbps, 11:7.2 kbps, 12:4.8 kbps, 13:2.4 kbps
Frequency of pseudoring signal
0:50 Hz, 1:25 Hz, 2:17 Hz
T-15-12
1
-
-
-
-
-
Detect with the new
method.
-
-
T-15-13
1
0
YES
NO
Drum replacement required
E019 displayed on an service
message displayed on an
call
operator call
-
-
-
-
-
-
-
-
-
-
-
-
T-15-14
0
-
-
-
-
-
Detect with the
existing method.
-
-
0013-1331
0013-1332
0013-7930
0013-7931
0013-7932
0013-1333
Advertisement
Table of Contents
