Nice E FIT M 817 BD Instructions And Warnings For Installation And Use
Tubular motor
Hide thumbs
Also See for E FIT M 817 BD:
- Quick manual (2 pages) ,
- Quick manual (2 pages) ,
- Instructions and warnings for installation and use (30 pages)
Related Manuals for Nice E FIT M 817 BD
Summary of Contents for Nice E FIT M 817 BD
- Page 1 Nice E FIT M 817 BD E FIT M 4012 BD E FIT M 1517 BD E FIT M 5012 BD E FIT M 3017 BD Tubular Motor EN - Instructions and warnings for installation and use...
-
Page 2: Installation Warnings
GENERAL WARNINGS: SAFETY - INSTALLATION - USE (original instructions in Italian) ATTENTION Important safety instructions. Follow all instructions as improper installation may cause serious damage ATTENTION Important safety instructions. It is important for you to comply with these instructions for your own and other people’s safety. -
Page 3: Product Description And Intended Use
Wireless technology makes even initial programming simple and user- friendly. • it is compatible with all Nice control electronics using the NRC radio system (trans- INSTALLATION OF THE MOTOR AND mitters and climate sensors, the latter can only be used if the motor is configured THE ACCESSORIES for operation in ONE-WAY mode);... -
Page 4: Programming And Adjustments
ONE-WAY mode, and thus can accept all one-way transmitters. If, within 15 To assemble and install the motor, refer to fig. 4. Moreover, consult the Nice product seconds of start-up, no one-way transmitter is paired with it, the motor will make a catalogue or go to www.niceforyou.com to choose the crown of the limit switch (fig. - Page 5 10 mm English – 4...
-
Page 6: General Warnings
“unit” corresponding to the automation you are programming before transmitters sending a command during a procedure. • To select transmitter compatible with the motor’s receiver, refer to the “Nice Screen” catalogue, which is also available on www.niceforyou.com. 4.4 - Positions in which the awnings, blind or •... - Page 7 COMMON to motors configured for either ONE-WAY or TWO-WAY communications Procedures which can only be completed with a Nice transmitter with the s, n, t, PRG, ESC keys (eg. “ERA P”, “ERA P BD”, “ERA W”, “ERA W BD”) GENERAL WARNINGS RELATING TO THE PROCEDURES •...
- Page 8 !!! (x 1) Observe the same awning and, at the start of a the movement will count 3 movements. DOWN movement, stop the movement IMMEDI- stop; ATELY, by pressing and releasing the button (1 time): A.2 - MANUAL programming of the UP (“0”) and DOWN (“1”) limit switches MONO BiDi NOTES AND WARNINGS •...
- Page 9 continues “ 0 ” Command Command an UP an DOWN movement movement Hold down the button and..wait for the awning to be stopped when it release the button. Hold down the button and wait... collides with the box (= UP limit switch = po- sition “0”).
- Page 10 A.5 - “RDC” Function: adjustment of the motor traction force when closing MONO BiDi NOTES AND WARNINGS • This function prevents the excessive traction of the canvas at the end of the closing manoeuvre. During the final phase of this manoeuvre, the function automatically reduces the motor traction torque, based on the factory setting or the one adjusted by the installer with the following procedure.
- Page 11 –– GROUP “B” PROCEDURES –– for motors configured for TWO-WAY communications Procedures which can only be completed with a Nice transmitter with the s, n, t, PRG, ESC keys (eg. “ERA P BD”, “ERA W BD”) GENERAL WARNINGS RELATING TO THE PROCEDURES •...
- Page 12 B.2 - TOTAL or PARTIAL deletion of memory BiDi NOTES AND WARNINGS • In order to carry out the following deletion procedures, the transmitter must be memorised in mode I. • To change the motor’s configuration (from TWO-WAY to ONE-WAY), after completing the “FULL deletion of the memory” procedure, it is necessary to switch the mo- tor off and then on again.
- Page 13 –– GROUP “C” PROCEDURES –– for motors configured for ONE-WAY communications procedures which can only be completed with a Nice “ERA P” or “ERA W” transmitter with the s, n, t, PRG, ESC keys GENERAL WARNINGS RELATING TO THE PROCEDURES •...
- Page 14 “PRG” and “ESC” buttons (like “ERA P” and “ERA W” transmitters). • To run procedures C.2.1.B and C.2.2.B you must have a new transmitter to memorise, chosen from the “Nice Screen” catalogue , and an old previously memorised transmitter.
- Page 15 continues = 5 sec sec. On the OLD transmitter: Hold count 2 movements; wait count 2 more move- release the but- On the NEW transmitter: hold down the but- down the button and wait... again... ments; ton. ton and ...
- Page 16 MONO NOTES AND WARNINGS • To run this procedure you need the climate sensor you want to memorise, chosen from the “Nice Screen” catalogue, and an old transmitter memorised in Mode I (see par. 4.5.1). • When performing the procedure, you can cancel the programming at any time by holding down n and t together for 4 seconds. Alternatively, do not press any keys and wait 60 seconds for the motor to perform 6 movements.
- Page 17 = 5 sec Hold down both buttons... release them after 5 count 5 movements. seconds; C.4.2 - Procedure run with a transmitter which has not yet been memorised NOTES AND WARNINGS • In order to carry out the following procedures, a transmitter with a PRG button should be used. ...
- Page 18 C.5 - Locking and unlocking the motor’s memory MONO NOTES AND WARNINGS • Locking the motor’s memory stops any other (unscheduled or unauthorised) transmitters being memorised in it. 4 (x 1) (x 1) (x 1) Press and release count 2 movements. Press and release count 2 movements.
-
Page 19: Disposal Of The Product
Over time, this compensates for Hereby, NICE S.p.A., declares that the radio equipment type E FIT M 817 BD, E FIT deformations in the structure due to wear and thermal cycles, so that the awning M 1517 BD, E FIT M 3017 BD, E FIT M 4012 BD, E FIT M 5012 BD, is in compliance always stops precisely at the Up limit position. - Page 20 Nice SpA Via Callalta, 1 31046 Oderzo TV Italy www.niceforyou.com info@niceforyou.com...