YASKAWA F7 Programming Manual page 78

The Drive has 6 multi-function contact digital inputs. By programming parameters H1-01 through H1-06, the user can assign specific
functions to each input. Below is a table with a complete list of all of the digital input functions according to control method (A1-02).
Not all functions are available for all control methods. Following the table is a more detailed description of each of the functions.
Parameter
Setting
0 3-Wire Control
1 Local/Remote Selection
2 Option/Inverter Selection
3 Multi-Step Frequency Reference 1 (factory default, H1-03)
4 Multi-Step Frequency Reference 2 (factory default, H1-04)
5 Multi-Step Frequency Reference 3
6 Jog Frequency Reference (factory default, H1-05)
7 Accel/Decel Time Selection 1
8 External Baseblock N.O. (factory default, H1-06)
9 External Baseblock N.C.
A Accel/Decel Ramp Hold
B External Overheat Alarm (OH2)
C Terminal A2 Enable
D V/f Control with PG Disabled
E ASR Integral Reset
F Terminal Not Used
10 MOP Increase
11 MOP Decrease
12 Forward Jog
13 Reverse Jog
14 Fault Reset (factory default, H1-02)
15 Fast-Stop N.O.
16 Motor 2 Selection
17 Fast-Stop N.C.
18 Timer Function
19 PID Disable
1A Accel/Decel Time Selection 2
1B Program Lockout
1C Trim Control Increase
1D Trim Control Decrease
1E Reference Sample Hold
20 External Fault, Normally Open, Always Detected, Ramp To Stop
21 External Fault, Normally Closed, Always Detected, Ramp To Stop
22 External Fault, Normally Open, During Run, Ramp To Stop
23 External Fault, Normally Closed, During Run, Ramp To Stop
External Fault, Normally Open, Always Detected, Coast to Stop
24
(factory default, H1-01)
25 External Fault, Normally Closed, Always Detected, Coast To Stop
26 External Fault, Normally Open, During Run, Coast To Stop
27 External Fault, Normally Closed, During Run, Coast To Stop
28 External Fault, Normally Open, Always Detected, Fast-Stop
29 External Fault, Normally Closed, Always Detected, Fast-Stop
2A External Fault, Normally Open, During Run, Fast-Stop
2B External Fault, Normally Closed, During Run, Fast-Stop
2C External Fault, Normally Open, Always Detected, Alarm Only
2D External Fault, Normally Closed, Always Detected, Alarm Only
2E External Fault, Normally Open, During Run, Alarm Only
2F External Fault, Normally Closed, During Run, Alarm Only
30 PID Integral Reset
31 PID Integral Hold
32 Multi-Step Reference 4
34 PID Soft Starter Cancel
Table 13 Multi-Function Input Selection
Function
Programming 70
Control Method (A1-02)
Open
V/f with
V/f Loop
PG
Vector
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
X O X
X O X
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
O O O
Flux
Vector
O
O
O
O
O
O
O
O
O
O
O
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O