YASKAWA F7 Programming Manual page 170

Parameter Parameter Name
No. Digital Operator Display
d1-01 Frequency Reference 1
Reference 1
d1-02 Frequency Reference 2
Reference 2
d1-03 Frequency Reference 3
Reference 3
d1-04 Frequency Reference 4
Reference 4
d1-05 Frequency Reference 5
Reference 5
d1-06 Frequency Reference 6
Reference 6
d1-07 Frequency Reference 7
Reference 7
d1-08 Frequency Reference 8
Reference 8
d1-09 Frequency Reference 9
Reference 9
d1-10 Frequency Reference 10
Reference 10
d1-11 Frequency Reference 11
Reference 11
d1-12 Frequency Reference 12
Reference 12
d1-13 Frequency Reference 13
Reference 13
d1-14 Frequency Reference 14
Reference 14
d1-15 Frequency Reference 15
Reference 15
d1-16 Frequency Reference 16
Reference 16
d1-17 Jog Frequency Reference
Jog Reference
Frequency Reference Upper
d2-01 Limit
Ref Upper Limit
Frequency Reference Lower
d2-02 Limit
Ref Lower Limit
Master Speed Reference
d2-03 Lower Limit
Ref1 Lower Limit
Denotes that parameter can be changed when the Drive is running.
Table A.1 F7 Parameter List (Continued)
Description
Preset Reference
Setting units are affected by o1-03.
Frequency reference when multi-function input "Multi-step speed
reference 1" is ON. Setting units are affected by o1-03.
Frequency reference when multi-function input "Multi-step speed
reference 2" is ON. Setting units are affected by o1-03.
Frequency reference when multi-function input "Multi-step speed
reference 1,2" is ON. Setting units are affected by o1-03.
Frequency reference when multi-function input "Multi-step speed
reference 3" is ON. Setting units are affected by o1-03.
Frequency reference when multi-function input "Multi-step speed
reference 1,3" is ON. Setting units are affected by o1-03.
Frequency reference when multi-function input "Multi-step speed
reference 2,3" is ON. Setting units are affected by o1-03.
Frequency reference when multi-function input "Multi-step speed
reference 1,2,3" is ON. Setting units are affected by o1-03.
Frequency reference when multi-function input "Multi-step speed
reference 4" is ON. Setting units are affected by o1-03.
Frequency reference when multi-function input "Multi-step speed
reference 1,4" is ON. Setting units are affected by o1-03.
Frequency reference when multi-function input "Multi-step speed
reference 2,4" is ON. Setting units are affected by o1-03.
Frequency reference when multi-function input "Multi-step speed
reference 1,2,4" is ON. Setting units are affected by o1-03.
Frequency reference when multi-function input "Multi-step speed
reference 3,4" is ON. Setting units are affected by o1-03.
Frequency reference when multi-function input "Multi-step speed
reference 1,3,4" is ON. Setting units are affected by o1-03.
Frequency reference when multi-function input "Multi-step speed
reference 2,3,4" is ON. Setting units are affected by o1-03.
Frequency reference when multi-function input "Multi-step speed
reference 1,2,3,4" is ON. Setting units are affected by o1-03.
Frequency reference when:
"Jog frequency reference" is selected via multi-function input
terminals. "Jog frequency reference" has priority over "multi-step
speed reference 1 to 4". d1-17 is also the reference for the JOG key
on the Digital Operator, and the multi-function inputs "forward
jog" and "reverse jog". Setting units are affected by o1-03.
Reference Limits
Determines maximum frequency reference, set as a percentage of
maximum output frequency (E1-04). If the frequency reference is
above this value, actual Drive speed will be limited to this value.
This parameter applies to all frequency reference sources.
Determines minimum frequency reference, set as a percentage of
maximum output frequency (E1-04). If frequency reference is
below this value, actual Drive speed will be set to this value. This
parameter applies to all frequency reference sources.
Determines minimum frequency reference, set as a percentage of
maximum output frequency (E1-04). If frequency reference from
analog input (A1, A2, and A3) is below this value, actual Drive
speed will be set to this value. This parameter applies only to
analog inputs A1, A2, and A3.
Programming 162
Control Method
Setting Factory
V/F
Range Setting
V/F w/
PG
0.00Hz Q Q
0.00Hz Q Q
0.00Hz Q Q
0.00Hz Q Q
0.00Hz A A
0.00Hz A A
0.00Hz A A
0.00Hz A A
0.00 to 0.00Hz A A
E1-04
Value
0.00Hz A A
0.00Hz A A
0.00Hz A A
0.00Hz A A
0.00Hz A A
0.00Hz A A
0.00Hz A A
6.00Hz Q Q
0.0 to
100.0% A A
110.0
0.0 to
0.0% A A
110.0
0.0 to
0.0% A A
110.0
Open
Flux
Loop
Vector
Vector
Q Q
Q Q
Q Q
Q Q
A A
A A
A A
A A
A A
A A
A A
A A
A A
A A
A A
A A
Q Q
A A
A A
A A