YASKAWA F7 Programming Manual page 177

Parameter Parameter Name
No. Digital Operator Display
Number of PG gear teeth 1
F1-12
PG # Gear Teeth1
Number of PG gear teeth 2
F1-13
PG # Gear Teeth2
PG open-circuit detection
F1-14 time
PGO Detect Time
AI-14 Input Selection
F2-01
AI-14 Input Sel
DI-08 / DI-16H2 Input
F3-01 Selection
DI Input
AO-08/AO-12 Channel 1
F4-01 Monitor Selection
AO Ch1 Sel
AO-08/AO-12 Channel 1
F4-02 Gain
AO Ch1 Gain
AO-08/AO-12 Channel 2
F4-03 Monitor Selection
AO Ch2 Sel
AO-08/AO-12 Channel 2
F4-04 Gain
AO Ch2 Gain
AO-08/AO-12 Channel 1
F4-05 Output Bias
AO Ch1 Bias
AO-08/AO-12 Channel 2
F4-06 Output Bias
AO Ch2 Bias
AO-12 Channel 1 Signal
F4-07 Level
AO Opt Level Ch1
AO-12 Channel 2 Signal
F4-08 Level
AO Opt Level Ch2
Denotes that parameter can be changed when the Drive is running.
Table A.1 F7 Parameter List (Continued)
Description
Sets the gear ratio between the motor shaft and the encoder (PG).
Input pulses from PG (PPR) x 60
F1-01
A gear ratio of 1 will be used if either of these parameters is set to
0. This function is not available in flux vector control.
Configures the PG open (PGO) function. PGO will be detected if
no PG pulses are detected for a time longer than F1-14. See F1-02.
AI-14 Setup
Sets the function for channel 1 to 3 of the AI-14B analog input
reference option board.
0: 3-channel individual (Channel 1: terminal A1, Channel 2:
terminal A2, Channel 3: terminal A3)
1: 3-channel addition (Summed values of channels 1 to 3 is the
frequency reference)
When set to 0, select 1 for b1-01. In this case, the multi-function
input "Option/Inverter selection" cannot be used.
DI-08, 16 Setup
Sets the function of the DI-08 or the DI-16H2 digital input option
board.
0: BCD 1% unit
1: BCD 0.1% unit
2: BCD 0.01% unit
3: BCD 1Hz unit
4: BCD 0.1Hz unit
5: BCD 0.01Hz unit
6: BCD (5-digit) 0.01Hz unit (only effective when DI-16H2 is
used.)
7: Binary input
When o1-03 is set to 2 or higher, the input will be BCD, and the
units will change to the o1-03 setting.
AO-08, 12 Setup
Sets the number of the monitor item to be output. (U1-
The following settings cannot be set:
4, 10 to 14, 25, 28, 29, 30, 34, 35, 39, 40, 41.
Sets the channel 1 gain.
Ex: Set F4-02 = 50% to output 100% at 5.0V output.
Sets the number of the monitor item to be output. (U1-
The following settings cannot be set:
4, 10 to 14, 25, 28, 29, 30, 34, 39, 40, 41.
Sets the channel 2 gain.
Ex: Set F4-02 = 50% to output 100% at 5.0V output.
Sets the channel 1 bias (100%/10V).
Ex: Set F4-05 = 50% to output 0% at 5.0V output.
Sets the channel 2 bias (100%/10V).
Ex: Set F4-06 = 50% to output 0% at 5.0V output.
Sets the range of the voltage output.
0: 0 to 10Vdc
1: -10 to +10Vdc
Sets the range of the voltage output.
0: 0 to 10Vdc
1: -10 to +10Vdc
Programming 169
Setting Factory
Range Setting
F1-13
x
0 to
F1-12
1000
0.0 to
2.0 sec
10.0
0 to 1
0 to 7
)
1 to 45
0.0 to
100.0%
1000.0
)
1 to 45
0.0 to
50.0%
1000.0
-110.0 to
110.0
-110.0 to
110.0
0 to 1
0 to 1
Control Method
V/F Open
V/F w/ Loop
PG Vector
0 - A -
0 - A -
- A -
0 A A A
0 A A A
2 A A A
A A A
3 A A A
A A A
0.0% A A A
0.0% A A A
0 A A A
0 A A A
Flux
Vector
-
-
A
A
A
A
A
A
A
A
A
A
A