Table of Contents
Advertisement
Section 8
iVIZION™2 Series Banknote Validator Foundation of Intelligent Validation
LED Error and Reject Codes
Identify the causes and solution for these indications from each Table's list and ensure that the relative
assembles are properly connected and/or harnessed, and that all of the Unit's Sensors are clean.
NOTE: If the error is not resolved, replace the relative Part(s) and Sensor(s).
LED Error Codes; General
Status LED
Error
Cash Box Full
Detected a Cash Box
Red Flashes
Full Condition
(1)
Reserved
Red Flashes
(2)
Sensor Adjust-
ment Error
Red Flashes
Abnormal Sensor
(3)
adjustment detected
Speed Error
Abnormal Transport
Red Flashes
Speed Adjustment
(4)
detected
FRAM Error
(Not calibrated)
Red Flashes
The Validator is not
(5)
calibrated
Transport Error
The Motor locked
Red Flashes
while transporting or
(6)
stacking a Banknote
Reject Error
The Motor Locked
Red Flashes
while rejecting a
(7)
Banknote
Stacker Error
(Pusher Plate
Movement)
Red Flashes
The Motor locked
(8)
while stacking a
Banknote
Pusher Plate
Position Error
Cannot detect the
Red Flashes
Position Sensor while
(9)
moving the Pusher
Plate
No Cash Box
The Cash Box is not
Red Flashes
seated
(10)
Reserved
Red Flashes
(11)
P/N 960-000231R_Rev. A
Table 21 LED Error Codes; General
Solution
•
Retrieving the Banknotes from the Cash Box.
•
Check that the relative Part(s) are properly
assembled and/or Harness are connected.
•
Clean and calibrate the relative Sensor(s).
-
•
Clean and calibrate the Sensors of the
Validator.
•
Remove any foreign objects if any.
•
Check that the relative Part(s) are properly
assembled and/or Harness are connected.
•
Clean and calibrate the relative Part(s) and
Sensor(s).
•
Remove any foreign objects if any.
•
Check that the relative Part(s) are properly
assembled and/or Harness are connected.
•
Remove any foreign objects if any.
•
Check that the relative Part(s) are properly
assembled and/or Harness are connected.
•
Remove any foreign objects if any.
•
Check that the relative Part(s) are properly
assembled and/or Harness are connected.
•
Firmly re-seat the Validator or the Cash Box.
•
Remove jammed Banknotes or foreign
objects if any.
•
Check that the relative Part(s) are properly
assembled and/or Harness are connected.
•
Clean and calibrate the relative Sensor(s).
•
Firmly re-seat the Validator or the Cash Box.
•
Check that the relative Part(s) are properly
assembled and/or Harness are connected.
•
Clean and calibrate the relative Sensor(s).
-
3 2
Troubleshooting
Relative Part/Sensor
•
Full Sensor
•
CPU Board CN12
•
MGU Board CN1 PT3, LED3
-
•
Validator
•
Feed Motor
•
Transport Encoder Board
CN1
•
MGU Board CN3
•
Validator
•
Feed Motor
•
Transport Encoder Board
CN1
•
MGU Board CN3
•
Feed Motor
•
Transport Encoder Board
CN1
•
MGU Board CN3
•
Stack Motor
•
Stack Encoder Board CN1
•
MGU Board CN4
•
Box Home Position Sensor
•
Stack Home Position Sensor
Board LED1, PT1
•
CPU Board CN2
•
Stack Motor
•
Stack Encoder Board CN1
•
MGU Board CN4
•
Cash Box Sensor
•
Validation CPU Board PL4,
PT3, PT4, CN2
•
Control CPU Board CN4
-
© 2022, JAPAN CASH MACHINE CO., LTD.
Advertisement
Table of Contents
