Standard Error And Reject Codes; Standard Error Codes; Table 21 Standard Led Error Codes - JCM GLOBAL TBV Series Integration Manual

Standard Error and Reject Codes

The Bezel LED indicates various solid/flashing Color lighting conditions when any of the Standard Errors
listed in Table 21 occur. Identify the cause and solutions for these indications from each Table listing and
ensure that the relative assembles are properly connected and/or harnessed, and that all of the Unit's 
Sensors are clean.
S E C
TANDARD RROR
Table 21 lists the various LED Flash Error Code causes & solutions.
On-line Off-line
LED Color LED Color
(Flash (Flash
Sequence) Sequence)
Yellow Yellow
(1) (1)
Yellow Yellow
(2) (2)
Yellow Yellow
(3) (3)
Yellow Yellow
(4) (4)
Yellow Yellow
(5) (5)
Yellow Yellow
(6) (6)
Yellow Yellow
(7) (7)
Red Red
(1) (1)
Red Red
(2) (2)
P/N 960-100925R_Rev. A {EDP #186705}
Transaction Based Validator Integration Guide
ODES

Table 21 Standard LED Error Codes

Error
When transporting a Banknote to the Cash Box, the Sensors are not detecting a
Banknote present condition when the time interval taken is too long or the number
of the Banknotes stuck is greater than specified value for that function.
Banknote Jam (in
[Solution] Check that the following parts are properly assembled and/or Harness
the Cash Box)
connected. Clean or adjust the following parts and Sensors.
[Relative Parts] Feed Motor, Stack Sensor, Feed-out Sensor.
If the error is not resolved, change the above related part or parts.
When transporting or returning a Banknote in the Transport Section, the Sensors
do not detect a Banknote present condition when the time interval taken is too long
or the number of the Banknotes stuck is greater than specified value for that
function.
Banknote Jam (in
[Solution] Check that the following parts are properly assembled and/or Harness
the Transport
connected. Clean or adjust the following parts and Sensors.
Section)
[Relative Parts] Feed Motor, BNF Entrance Sensor, BNF Assignation Sensor,
Entrance Sensor, Centering Sensor, Line Sensor, Feed-out Sensor.
If the error is not resolved, change the above related part or parts.
While performing a BNF Banknote assignation, the Sensors do not detected a
Banknote present condition when the time interval taken is too long or the number
of the Banknotes stuck is greater than specified value for that function.
[Solution] Check that the following parts are properly assembled and/or Harness
Banknote Chain
connected. Clean or adjust the following parts and Sensors.
[Relative Parts] BNF Feed Roller, BNF Retard Roller, BNF Assignation Sensor,
Entrance Sensor, Feed-out Sensor.
If the error is not resolved, change the above related part or parts.
The Cash Box has been removed.
[Solution] Check that the following parts are properly assembled and/or Harness
connected. Clean or adjust the following parts and Sensors.
Cash Box Removal
[Relative Parts] Cash Box Sensor.
If the error is not resolved, change the above related part or parts.
Sensors detect Banknotes remaining in path or none exist during an abnormal
timing operation.
[Solution] Check that the following parts are properly assembled and/or Harness
connected. Clean or adjust the following parts and Sensors.
Fraud Detection
[Relative Parts] Line Sensor, Feed-out Sensor, Cash Box Feed-out Sensor, Side
Sensor.
If the error is not resolved, change the above related part or parts.
Sensors detect that the Cash Box Lock has been opened.
[Solution] Check that the following parts are properly assembled and/or Harness
Cash Box Lock
connected. Clean or adjust the following parts and Sensors.
Released
[Relative Parts] Cash Box Lock Sensor.
If the error is not resolved, change the above related part or parts.
Sensors detect that the Upper Cover of the Transport Section has been opened.
[Solution] Check that the following parts are properly assembled and/or Harness
Transport Section
connected. Clean or adjust the following parts and Sensors.
Upper Cover Open
[Relative Parts] Entrance Sensor, Centering Sensor.
If the error is not resolved, change the above related part or parts.
While stacking a Banknote, the Cash Box Full Sensors detect that the Cash Box is
full.
[Solution] Check that the following parts are properly assembled and/or Harness
Cash Box Full
connected. Clean or adjust the following parts and sensors.
[Relative Parts] Cash Box Full Sensor, Pusher Mechanism, Pusher Plate.
If the error is not resolved, change the above related part or parts.
While operating the Feed Motor, no pulse inputs exist greater than the rated value.
[Solution] Check that the following parts are properly assembled and/or Harness
Feed Motor
connected. Clean or adjust the following parts and Sensors.
Lock-up Problem
[Relative Parts] Feed Motor, Feed Encoder.
If the error is not resolved, change the above related part or parts.
Causes and Solutions
© 2010, Japan CashMachine Co, Limited
2 2