Tektronix AWG7000 Series Service Manual page 104

Troubleshooting
Table 4-7: Calibration error (cont.)
Error code Error log message
260000105 The difference of ch1_ram_data_timing_1 and
ch2_ram_data_timing_1 is larger than 96.(@10GHz)
260000107 The difference of ch1_ram_data_timing_2 and
ch2_ram_data_timing_2 is larger than 96.(@8GHz)
260000108 The difference of ch1_ram_data_timing_1 -
ch1_ram_data_timing_2 is larger than 96.
260000109 The difference of ch2_ram_data_timing_1 -
ch2_ram_data_timing_2 is larger than 96.
260000011 The Cal value is not found.(ch1_pld_timing_1@10GHz)
260000012 The Cal value is not found.(ch2_pld_timing_1@10GHz)
260000013 The Cal value is not found.(ch1_pld_timing_2@8GHz)
260000014 The Cal value is not found.(ch2_pld_timing_2@8GHz)
260000015 The Cal value is not found.(ch1_pld_timing_3@10GHz)
260000016 The Cal value is not found.(ch2_pld_timing_3@10GHz)
260000017 Temperature changed 5 degrees or more.(@PLD Timing Cal.)
260000111 The difference of ch1_pld_timing_1 and ch2_pld_timing_1 is
larger than 48.(@10GHz)
260000113 The difference of ch1_pld_timing_2 and ch2_pld_timing_2 is
larger than 48.(@8GHz)
260000115 The difference of ch1_pld_timing_3 and ch2_pld_timing_3 is
larger than 48.(@10GHz)
260001005 Invalid NG Areas.(ch1_pld_timing@10GHz)
260001006 Invalid NG Areas.(ch2_pld_timing@10GHz)
260001007 Invalid NG Areas.(ch1_pld_timing@8GHz)
260001008 Invalid NG Areas.(ch2_pld_timing@8GHz)
260000021 The Cal value is not found.(tek15_ch1_timing_1)
260000022 The Cal value is not found.(tek15_ch2_timing_1)
260000023 The Cal value is not found.(tek15_ch1_timing_2)
260000024 The Cal value is not found.(tek15_ch2_timing_2)
260000025 A coefficient is not also 5 or 6.(tek15_ch1_k)
260000026 A coefficient is not also 5 or 6.(tek15_ch2_k)
260000027 The Cal value is not found.(tek15_ch1_ng_f)
260000028 The Cal value is not found.(tek15_ch2_ng_f)
260000029 Temperature changed 5 degrees or more.(@Magic Cal.)
260000121 The difference of tek15_ch1_timing_1 and tek15_ch2_timing_1 is
larger than 150ps.
260000123 The difference of tek15_ch1_timing_2 and tek15_ch2_timing_2 is
larger than 150ps.
260000125 tek15_ch1_k and tek15_ch2_k are not equal.
260001009 Invalid NG Areas.(ch1@Magic Cal.)
260001010 Invalid NG Areas.(ch2@Magic Cal.)
270000000 HwExecYigCal PLL read error
270000001 HwExecYigCal PLL 5GHz offset under 2048 vtune=xxxx
4-52
Possible defect Note
on board
AWG10G AWG10G: U400, U500, U510
AWG10G AWG10G: U400, U500, U510
AWG10G AWG10G: U400A, U500A, U510A
AWG10G AWG10G: U400B, U500B, U510B
AWG10G AWG10G: U400A
AWG10G AWG10G: U400B
AWG10G AWG10G: U400A
AWG10G AWG10G: U400B
AWG10G AWG10G: U400A
AWG10G AWG10G: U400B
AWG10G AWG10G: U400
AWG10G AWG10G: U400
AWG10G AWG10G: U400
AWG10G AWG10G: U400xA
AWG10G AWG10G: U400xB
AWG10G AWG10G: U400xA
AWG10G AWG10G: U400xB
AWG10G AWG10G: U300A
AWG10G AWG10G: U300B
AWG10G AWG10G: U300A
AWG10G AWG10G: U300B
AWG10G AWG10G: U300A
AWG10G AWG10G: U300B
AWG10G AWG10G: U300A
AWG10G AWG10G: U300B
AWG10G AWG10G: U300
AWG10G AWG10G: U300
AWG10G AWG10G: U300
AWG10G AWG10G: U300xA
AWG10G AWG10G: U300xB
AWG10G AWG10G: U1000, U1040
CLK10G CLK10G: U3200, U3250, Y3280
AWG7000 Series Service Manual