Tektronix AWG7000 Series Service Manual page 100

Troubleshooting
Table 4-6: Diagnostics error (cont.)
Error code Error log message
141000017 Analog Level Diag CH1 10db attenuator gain balance failed. OUT10G
141000018 Analog Level Diag CH1 20db attenuator gain balance failed. OUT10G
141000019 Analog Level Diag CH1 filter 50mhz gain balance failed.
141000020 Analog Level Diag CH1 filter 200mhz gain balance failed.
141000021 Analog Level Diag CH1 amp gain balance failed.
1420M0001 Marker Level Diag CH1 MARKER M offset failed.
1420M0002 Marker Level Diag CH1 MARKER M positive offset failed.
1420M0003 Marker Level Diag CH1 MARKER M negative offset failed.
1420M0004 Marker Level Diag CH1 MARKER M amplitude failed.
1420M0005 Marker Level Diag CH1 MARKER M amplitude correction
failed.
150000000 The error occurred in the EEPROM read. 1st=FST
2nd=SND
FST: the data that is received from EEPROM at the first read
check
SND: the data that is received from EEPROM at the second
read check, which is implemented after writing 0x55 to
EEPROM
150000001 Message varies depending on the situation.
1510P0001 Analog Level Diag CH2 positive (negative) 5db attenuator
failed. expected 0.56234, actual xxxxx
1510P0002 Analog Level Diag CH2 positive (negative) 5db attenuator
failed. expected 0.56234, actual xxxxx
1510P0003 Analog Level Diag CH2 positive (negative) 10db attenuator
failed. expected 0.31627, actual xxxxx
1510P0004 Analog Level Diag CH2 positive (negative) 20db attenuator
failed. expected 0.100000, actual xxxxx
1510P0005 Analog Level Diag CH2 positive (negative) 50mhz filter
failed. expected 0.992, actual xxxxx
1510P0006 Analog Level Diag CH2 positive (negative) 200mhz filter
failed. expected 0.998, actual xxxxx
1510P0007 Analog Level Diag CH2 positive (negative) amplitude cal
failed. expected 2.07, actual xxxxx
1510P0008 Analog Level Diag CH2 positive (negative) hfd dac
reference failed.
1510P0009 Analog Level Diag CH2 positive (negative) output offset
failed. expected 0.50V(0.0V), actual xxxxx
151000010 Analog Level Diag CH2 internal offset 8bit failed. expected
0.0mV, actual xxxxxmV
151000011 Analog Level Diag CH2 internal offset 10bit failed. expected
0.0mV, actual xxxxxmV
151000012 Analog Level Diag CH2 can't find 8bit outamp offset cross
point. expected 0.0mV, actual pos: xxxxxmV, neg: xxxxxmV
151000013 Analog Level Diag CH2 can't find 10bit outamp offset cross
point. expected 0.0mV, actual pos: xxxxxmV, neg: xxxxxmV
4-48
Possible defect Note
on board
OUT10G: K620, K720
OUT10G: K630, K730
OUT10G OUT10G: K660, K760
OUT10G OUT10G: K670, K770
OUT10G OUT10G: U800
OUT10G U120,U170,U230,U240,U330,U340
OUT10G U120,U170,U230,U240,U330,U340
OUT10G U120,U170,U230,U240,U330,U340
OUT10G U120,U170,U230,U240,U330,U340
OUT10G U120,U170,U230,U240,U330,U340
OUT10G OUT10G-CH2: U500, U550
OUT10G OUT10G-CH1: U500, U550
OUT10G OUT10G: K610, K710
OUT10G OUT10G: K610, K710
OUT10G OUT10G: K620, K720
OUT10G OUT10G: K630, K730
OUT10G OUT10G: K660, K760
OUT10G OUT10G: K670, K770
OUT10G OUT10G: U800
AWG10G AWG10G: U100B, U150B
OUT10G OUT10G: U900, U910, U920
AWG10G AWG10G: U100B, U150B
AWG10G AWG10G: U100B, U150B
AWG10G AWG10G: U100B, U150B
AWG10G AWG10G: U100B, U150B
AWG7000 Series Service Manual