Tektronix AWG7000 Series Service Manual page 103

Table 4-7: Calibration error (cont.)
Error code Error log message
220000000 HwExecMarkerDelayCal (channel=1) A maximum and a minimum
difference are smaller than 80ps at coarse=15
220000001 HwExecMarkerDelayCal (channel=2) A maximum and a minimum
difference are smaller than 80ps at coarse=15
220000002 HwExecMarkerDelayCal (channel=1) Frequency measurement
cannot be performed.
220000003 HwExecMarkerDelayCal (channel=2) Frequency measurement
cannot be performed.
220000004 HwExecMarkerDelayCal (channel=1) A maximum value is smaller
than 300ps at coarse=15.
220000005 HwExecMarkerDelayCal (channel=2) A maximum value is smaller
than 300ps at coarse=15.
220000006 HwExecMarkerDelayCal (channel=1) There are not data in
ascending order coarse=%d
220000007 HwExecMarkerDelayCal (channel=2) There are not data in
ascending order coarse=%d
230000000 N/A
240000000 N/A
250000000 The Cal value is not found.(10G-Write)
250000001 The Cal value is not found.(8G-Write)
250000002 The Cal value is not found.(10G-Read)
250000004 The Cal value is not found.(Waveform RAM Write Timing CH1)
250000005 The Cal value is not found.(Waveform RAM Write Timing CH2)
250000006 Invalid NG Areas.(10G-Write)
250000007 Invalid NG Areas.(8G-Write)
260000200 Waveform write error.
260000001 The Cal value is not found. (ch1_ram_address_timing_1@10GHz) AWG10G
260000002 The Cal value is not found. (ch2_ram_address_timing_1@10GHz) AWG10G
260000003 The Cal value is not found. (ch1_ram_address_timing_1@8GHz) AWG10G
260000004 The Cal value is not found. (ch2_ram_address_timing_1@8GHz) AWG10G
260000005 The Cal value is not found. (ch1_ram_data_timing_1@10GHz)
260000006 The Cal value is not found. (ch2_ram_data_timing_1@10GHz)
260000007 The Cal value is not found. (ch1_ram_data_timing_2@8GHz)
260000008 The Cal value is not found. (ch2_ram_data_timing_2@8GHz)
260000101 The difference of ch1_ram_address_timing_1 and
ch2_ram_address_timing_1 is larger than 96.(@10GHz)
260000103 The difference of ch1_ram_address_timing_2 and
ch2_ram_address_timing_2 is larger than 96.(@8GHz)
260001001 Invalid NG Areas.(ch1_ram_address_timing@10GHz)
260001002 Invalid NG Areas.(ch2_ram_address_timing@10GHz)
260001003 Invalid NG Areas.(ch1_ram_address_timing@8GHz)
260001004 Invalid NG Areas.(ch2_ram_address_timing@8GHz)
AWG7000 Series Service Manual
Possible defect Note
on board
AWG10G AWG10G: U1000, U100A
AWG10G AWG10G: U1000, U100B
AWG10G AWG10G: U1000, U100A
AWG10G AWG10G: U1000, U100B
AWG10G AWG10G: U100A
AWG10G AWG10G: U100B
AWG10G AWG10G: U1000, U100A, U195A
AWG10G AWG10G: U1000, U100B, U195B
AWG10G AWG10G: U100A/B, U4000
AWG10G AWG10G: U100A/B, U4000
AWG10G AWG10G: U1000, U400
AWG10G AWG10G: U1000, U400
AWG10G AWG10G: U1000, U400
AWG10G AWG10G: U400A, U500A, U510A
AWG10G AWG10G: U400B, U500B, U510B
AWG10G U400PA
AWG10G U400PA
AWG10G AWG10G: U400, U500, U510
AWG10G: U400A, U500A, U510A
AWG10G: U400B, U500B, U510B
AWG10G: U400A, U500A, U510A
AWG10G: U400B, U500B, U510B
AWG10G AWG10G: U400A, U500A, U510A
AWG10G AWG10G: U400B, U500B, U510B
AWG10G AWG10G: U400A, U500A, U510A
AWG10G AWG10G: U400B, U500B, U510B
AWG10G AWG10G: U400, U500, U510
AWG10G AWG10G: U400, U500, U510
AWG10G AWG10G: U400xA
AWG10G AWG10G: U400xB
AWG10G AWG10G: U400xA
AWG10G AWG10G: U400xB
Troubleshooting
4-51