Table of Contents
Advertisement
4. User adjustment
4.1 Names and functions of front panel parts
1
2
DEGAUSS
SET UP
POWER
HTM–1005R
22
1. POWER switch
2. DEGAUSS switch
3. MENU/ENT switch
4. PRE switch
5. ESC switch
6. UTILITY switch
7. ASPECT switch
8. U-SCAN switch
9. PCR switch
The following terms used in the descriptions have the meanings
below.
• SDTV:
525i, 625i
• HDTV:
1035i, 1080i, 720p
• SD-SDI: SDTV (525i, 625i)'s SDI
• HD-SDI: HDTV (1035i, 1080i, 720p)'s SDI
1. POWER switch and LED
This switch turns ON/OFF the power to the monitor.
If AC power and DC power are supplied at the same time, AC
power will override DC power.
This LED goes on when the power to the monitor is turned on.
If it blinks, think that a warning is given and take measures
according to "Handling precautions" on Page 5.
2. DEGAUSS switch
This switch degausses the magnetization of the CRT shadow
mask. Degaussing also takes place automatically at power-on.
It is useless to press this switch repeatedly in rapid succession.
It must be pressed at intervals of two to three minutes.
Although the degaussing system built into this machine is
designed for use in severe environments, use an external
degaussing system to degauss any extreme magnetization.
3. MENU/ENT switch
This switch is used to turn over the pages of a menu. It also
serves as the data registration (ENT) switch when the PRESET
setting screen is displayed.
4. PRE switch
This switch can display each PRESET setting screen.
3
4
5
6
7
MENU/ENT
PRE
ESC
UTILITY
ASPECT
A
INPUT
APT
MONO
ANALOG
SDI
B
21 20
19
18
17
16
10. CHROMA manual control
11. BRIGHTNESS manual control
12. CONTRAST manual control
13. AUDIO manual volume control
14. MARKER switch
15. SCREEN switch
16. MONO switch
17. APERTURE switch
8
9
10
CHROMA
U–SCAN
PCR
SCREEN
MARK
15
14
18 to 21: INPUT changeover switches.
When MENU or PRESET data is changed,
they serve as switches for moving cursors
or increasing/decreasing data.
18. ch A select/Up switch
19. SDI input select/right-shift switch
20. ch B select/Down switch
21. ANALOG input select/left-shift switch
22. SET UP switch
5. ESC switch
When a menu is displayed, this switch clears the menu items.
When the PRESET setting screen is displayed, it rests data to its
previous state.
6. UTILITY switch
This switch serves as assigned using the menu item 2-3.
(1) INPUT selecting switch
If INPUT selecting is assigned to this switch, the switching
between input signals will be done. (No switching takes place
when the optional module is not mounted.)
In the case of analog input, the SYNC INT/EXT settings are
memorized for each channel (composite input A/B, YPbPr/
RGB input A/B), so that the switching takes place
automatically at the same time the channel is changed.
The ASPECT settings (4:3/16:9) are also memorized for each
channel (composite input A/B, YPbPr/RGB input A/B, SD-
SDI ch A/B, HD-SDI ch A/B), so that the switching takes
place automatically at the same time the channel is changed.
In addition, the switching between the settings of horizontal
or vertical screen sizes, horizontal raster phases, etc. takes
place automatically according to the format.
(2) COMB (for DE-1051)
(3) SYNC (SYNC INT/EXT switching)
(4) FILE (REF, FILE 1 to 3 switching)
(5) AUDIO CH (for DKM-1051AV or DKM-1051AVD)
17
11
12
13
BRIGHT
CONT
AUDIO
Front Panel
Advertisement
Table of Contents
