Important Information - SMART Board 6075S Installation And Maintenance Manual

Important information

WARNING
Failure to follow the installation instructions included with
l
the display could result in injury and product damage
which may not be covered by the warranty.
Do not open or disassemble the display. You risk
l
electrical shock from the high voltage inside the casing.
Opening the casing also voids the warranty.
Do not stand (or allow children to stand) on a chair to
l
touch the surface of the display. Rather, mount the
product at the appropriate height.
To reduce the risk of fire or electric shock, do not expose
l
the display to rain or moisture.
If the display requires replacement parts, make sure the
l
service technician uses replacement parts specified by
SMART Technologies or parts with the same
characteristics as the original.
Ensure that any cables that cross the floor to the display
l
are properly bundled and marked to avoid a trip hazard.
Do not insert objects inside the cabinet ventilation holes,
l
because they could touch dangerous voltage points and
cause electric shock, fire or product damage which may
not be covered by the warranty.
Do not place heavy objects on the power cable. Damage
l
to the cable could cause shock, fire, or product damage
which may not be covered by the warranty.
Use only extension cords and outlets that can fully
l
accommodate the display's polarized plug.
Use the power cable provided with the display. If a power
l
cable is not supplied, contact your supplier. Use only
power cables that match the AC voltage of the power
outlet and that comply with your country's safety
standards.
If the glass is broken, do not touch the liquid crystal. To
l
prevent injury, handle glass fragments with care when
disposing of them.
Do not move or mount the display by connecting rope or
l
wire to its handles. The display is heavy, and failure of the
rope, wire, or handle could lead to injury.
Use only VESA-approved mounts.
l
Disconnect the display's power cable from the wall outlet
l
and seek assistance from qualified service personnel if
any of the following occur:
The power cable or plug is damaged
o
Liquid is spilled into the display
o
smarttech.com/kb/171414
Objects fall into the display
o
The display is dropped
o
Structural damage, such as cracking, occurs
o
The display behaves unexpectedly when you
o
follow operating instructions
CAUTION
Turn off the display before cleaning its screen.
l
Otherwise, you may scramble the desktop icons or
inadvertently activate applications when you wipe the
screen.
Avoid setting up and using the display in an area with
l
excessive levels of dust, humidity, and smoke.
Make sure an electrical socket is near the display and
l
remains easily accessible during use.
In Europe, the display should be used only with European
l
TN and TT power distribution systems.
It is not suitable for older, IT-type power distribution
systems found in some European countries. "This system
(IT-type) is widely used isolated from earth, in some
installations in France, with impedance to earth, at
230/400V, and in Norway, with voltage limiter, neutral
not distributed, at 230V line-to-line."
Contact qualified personnel if you're uncertain of the type
of power system available where you're installing the
display.
The accessory slot's maximum available power is 60 W.
l
The slot is not a limited power source. To reduce the risk
of fire, make sure that accessories connecting to the slot
satisfy the fire enclosure requirements of IEC 60950-1
and IEC 62368-1.
You must connect the USB cable that came with the
l
display to a computer that has a USB compliant interface
and that bears the USB logo. In addition, the USB source
computer must be compliant with IEC 60950-1 and/or
IEC 62368-1. It must be certified by UL or CSA or another
NRTL / SCC certified body to CSA/UL 60950-1 or CSA/UL
62368-1 and it must have the CE marking. This is for
operating safety and to avoid damage to the display.
Wait five minutes before removing accessories from the
l
display's OPS slot to allow the accessory to cool.
3