evertz 7882J2KX-IPASI User Manual
  1. Manuals
  2. Brands
  3. evertz Manuals
  4. Media Converter
  5. 7882J2KX-IPASI
  6. User manual

evertz 7882J2KX-IPASI User Manual

Single channel encoder/decoder
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
© Copyright 2017
EVERTZ MICROSYSTEMS LTD.
5292 John Lucas Drive
Burlington, Ontario,
Canada L7L 5Z9
Phone:
+1 905-335-3700
Sales:
sales@evertz.com
Tech Support: service@evertz.com
Web Page:
http://www.evertz.com
Version 1.0, March 2017
The material contained in this manual consists of information that is the property of Evertz Microsystems and is intended solely for the use of
purchasers of the 7882J2KX-IPASI series product. Evertz Microsystems expressly prohibits the use of this manual for any purpose other than the
operation of the 7882J2KX-IPASI series product. Due to on going research and development, features and specifications in this manual are
subject to change without notice.
All rights reserved. No part of this publication may be reproduced without the express written permission of Evertz Microsystems Ltd. Copies of
this manual can be ordered from your Evertz dealer or from Evertz Microsystems.
7882J2KX-IPASI
Single Channel J2K Encoder/Decoder
User Manual
Fax: +1 905-335-3573
Fax: +1 905-335-7571

Advertisement

Table of Contents
loading

Related Manuals for evertz 7882J2KX-IPASI

Summary of Contents for evertz 7882J2KX-IPASI

  • Page 1 Version 1.0, March 2017 The material contained in this manual consists of information that is the property of Evertz Microsystems and is intended solely for the use of purchasers of the 7882J2KX-IPASI series product. Evertz Microsystems expressly prohibits the use of this manual for any purpose other than the operation of the 7882J2KX-IPASI series product.
  • Page 2 This page left intentionally blank...
  • Page 3 IMPORTANT SAFETY INSTRUCTIONS The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “Dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (Servicing) instructions in the literature accompanying the product.
  • Page 4 WARNING Changes or Modifications not expressly approved by Evertz Microsystems Ltd. could void the user’s authority to operate the equipment. Use of unshielded plugs or cables may cause radiation interference. Properly shielded interface cables...

  • Page 5: Table Of Contents

    3.2. CARE AND HANDLING OF OPTICAL FIBER WHEN USING SFP MODULES ....7 3.2.1. Handling and Connecting Fibers ................7 3.3. HARDWARE INSTALLATION ....................8 3.3.1. Three Different Ways to Control and Configure the 7882J2KX-IPASI ......8 3.3.2. Module Installation ..................... 8 3.3.3. Control Port Configurations for the 7882J2KX-IPASI ..........9 WEB INTERFACE ........................
  • Page 6 7882J2KX-IPASI Single Channel J2K Encoder/Decoder 5.1. SYSTEM TAB ........................32 5.2. PRODUCT FEATURES ...................... 35 5.3. DECODER CONTROL ....................... 37 5.4. DECODER AUDIO CONTROL TAB .................. 40 5.5. DECODER MONITOR TAB ....................41 5.6. INPUT AUDIO PROC CONTROL ..................43 5.7.
  • Page 7 7882J2KX-IPASI Single Channel J2K Encoder/Decoder Figures Figure 1-1 : 7882J2KX-IPASI Encoder Block Diagram ..................2 Figure 1-2 : 7882J2KX-IPASI Decoder Block Diagram ..................2 Figure 3-1 : 7882J2KX-IPASI Rear Plate ......................5 Figure 3-2 : RJ-45 Connector Pin-Out Locations ..................... 6 Figure 3-3 : 7800 Chassis ..........................
  • Page 8 7882J2KX-IPASI Single Channel J2K Encoder/Decoder This page left intentionally blank Page - iv Revision 1.0...
  • Page 9 Evertz products are for informational use only and are not warranties of future performance, either expressed or implied. The only warranty offered by Evertz in relation to this product is the Evertz standard limited warranty, stated in the sales contract or order confirmation form.
  • Page 10 7882J2KX-IPASI Single Channel J2K Encoder/Decoder This page left intentionally blank Page - vi Revision 1.0...

  • Page 11: Overview

    The 7882J2KX-IPASI supports dual network interfaces (main & redundant) to ensure robust transmission over wide area networks. The 7882J2KX-IPASI includes a dedicated control port that offers a built-in web server for quick and easy configuration, including true SNMP control from the award winning VistaLINK NMS and can be ®...

  • Page 12: Figure 1-1 : 7882J2Kx-Ipasi Encoder Block Diagram

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder Figure 1-1 : 7882J2KX-IPASI Encoder Block Diagram Figure 1-2 : 7882J2KX-IPASI Decoder Block Diagram Page - 2 Revision 1.0...

  • Page 13: Specifications

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder SPECIFICATIONS 2.1. SERIAL VIDEO INPUT SPECIFICATIONS Standard: HD-SDI (SMPTE ST 292-1) SD-SDI (SMPTE ST 259-C) Video Resolution: 1920x1080 @ 25, 29.97 1280x720 @ 50, 59.94 720x576 @ 25Hz (ITU-R BT.656-4) 720x480 @ 29.97Hz (SMPTE 125M)

  • Page 14: Configuration & Mgmt

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder 2.6. CONFIGURATION & MGMT Web Server: Integrated HTTP with full control SNMP: VistaLINK remote control and monitoring via Frame Controller 2.7. ELECTRICAL Input Voltage: Auto ranging 100 – 240VAC Power: <48W EMI/RFI: Complies with FCC regulations for class-A devices Complies with EU EMC directive 2.8.

  • Page 15: Getting Started

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder GETTING STARTED The 7882J2KX-IPASI module comes with a companion rear plate that occupies two slots in the frame. Figure 3-1 : 7882J2KX-IPASI Rear Plate IN 1, 2: BNC connectors used to input HD/SD SDI with embedded audio.

  • Page 16: Connecting To An Ethernet Network

    CONNECTING TO AN ETHERNET NETWORK 3.1.1. Ethernet Connection for the Control Port The 7882J2KX-IPASI is designed to be used with either 10Base-T (10 Mbps) or 100Base-TX (100 Mbps), also known as Fast Ethernet cabling systems. When connecting for 10Base-T systems, category 3, 4, or 5 UTP (unshielded twisted pair) cable as well as EIA/TIA –...

  • Page 17: Care And Handling Of Optical Fiber When Using Sfp Modules

    Brown/White or Brown Table 3-2 : 1000BaseT Straight Through Wiring Connections The maximum cable run between the 7882J2KX-IPASI and the supporting hub is 328 ft (100 m). The maximum combined cable run between any two end points (i.e. 7882J2KX-IPASI and PC/laptop via network hub) is 675 feet (205 m).

  • Page 18: Hardware Installation

    7800FC (frame controller) with 7882J2KX-IPASI installed in frame. ® When using the Control Port on the 7882J2KX-IPASI, each module will need to be assigned to an IP address in order to communicate. When using a frame controller, multiple cards can be inserted in the frame and be controlled using only one IP address of the frame controller.

  • Page 19: 3.3.3. Control Port Configurations For The 7882J2Kx-Ipasi

    ® module, this step is not necessary for setting the control port on the 7882J2KX-IPASI. 1. Connect the Evertz serial upgrade cable (ribbon cable) to the 2x3 header at the front edge of the 7882J2KX-IPASI card. 2. Start a terminal program and configure the port settings.

  • Page 20: Figure 3-6 : Com Port - Network Settings

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder 4. From the main menu, several selections are available. Select Network Setup and the menu illustrated below will appear. Set the desired network addresses per your requirement. After entering all settings choose Exit two times to save configurations and get back to main menu. The card must be rebooted for all the network settings to take effect.

  • Page 21: Web Interface

    Figure 4-1 : WebEASY – Login Menu ® Login and password are “root” and “evertz” respectively.  Due to the size of the certain menu tabs, we will be breaking up screen tab images into multiple images. Some of the screen shots will also require the user to zoom in to see the image more clearly.

  • Page 22: Sytem Tab

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder 4.1. SYTEM TAB Figure 4-2 : WebEASY – System Tab Part 1 ® Card Mode Control Card Mode: This monitor displays the behavior of the module. Firmware Version Firmware Version: This monitor displays the current firmware version.
  • Page 23 Syslog is a valuable tool for debugging the device operation. It is essentially serial readouts over IP, sent to a dedicated server. If issues are present, Evertz can help install and setup a syslog server for constant monitoring of the device activity.

  • Page 24: Figure 4-3 : Webeasy

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder Figure 4-3 : WebEASY – System Tab Part 2 ® Data Port Monitor (Data Ports 1 and 2) SFP Part Number: This parameter returns the part number of the SFP located in the Data Port.

  • Page 25: Product Features Tab

    - Product Features Tab ® Product License Product License File: This parameter allows the user to apply new License key provided by Evertz Microsystems Ltd. Reserved for future use. The 7882J2KX-IPASI supports 1 encoder and 1 decoder by default. Product Serial Number: This parameter displays the card serial number. This is required by Evertz when generating or updating license files on the 7882J2KX-IPASI.

  • Page 26: Decoder Control Tab

    Product Feature Supported Product Feature Name: This parameter displays the possible product features supported on the 7882J2KX-IPASI if it is available on the platform. Product Feature Supported: This parameter displays the status of features currently supported. Enabled means the license key is installed and disabled means the license key is not installed.
  • Page 27 7882J2KX-IPASI Single Channel J2K Encoder/Decoder Manual PID Select allows the user to define the Manual PID Control section. • Program Number • Video PID Select • PCR PID Select • VANC PID Select Auto Program Select Mode: Options are First Program in PAT or Lowest Program Number.

  • Page 28: Decoder Control Tab - Part 2

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder Figure 4-6 : WebEASY – Decoder Control Tab - Part 2 ® Input Profile For Main and Backup: Input Source Select: This control is used to select the physical input source for the Decoder. Options are Data 1, Data 2, ASI 1 or ASI 2.

  • Page 29: Decoder Audio Control Tab

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder IGMPV3 SSM Profile Control For Main and Backup IGMP Source 1 to 6: The user can add the required SSM sources for V3. Switch Over Control User Redundancy Mode: This control is used to enable redundancy mode for switch over on a loss input.

  • Page 30: Decoder Monitor Tab

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder 4.5. DECODER MONITOR TAB Figure 4-8 : WebEASY – Decoder Monitor Tab ® Input Monitor Status: This field displays if an input is detected on the decoder. Bitrate: This field displays the detected bitrate for the input.

  • Page 31: Input Audio Proc Control Tab

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder Video Monitor Program Number: This field displays the program number. Program Name: This field displays the program name. PMT PID: This field displays the PMT PID. PCR PID: This field displays the PCR PID. Video PID: This field displays the Video PID.

  • Page 32: Encoders Control Tab

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder Input Audio Proc Control Enable Audio Proc: If this is disabled, Audio will follow the embedded audio. If this parameter is enabled, it allows the user to select which incoming embedded audio channel goes to which Encoder source channel.
  • Page 33 7882J2KX-IPASI Single Channel J2K Encoder/Decoder Total TS Bit Rate: This parameter allows the user to select the output TS Bitrate in kbps. The device will automatically adjust the bitrate for video based on audio and advanced PID configuration to maintain the set TS bitrate.

  • Page 34: Figure 4-11 : Webeasy

    – Encoders Control Tab - Part 2 ® Audio PID Assignment Audio 1 to 4 PID: The 7882J2KX-IPASI has 4 x Audio Pids. These parameters allow the user to select the Audio PID number. Audio MUX Control For Audio 1 to 4: First AES On Output: This parameter allows the user to select the de-embedded audio pair on the audio encoder.

  • Page 35: Encoders Monitor Tab

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder 4.8. ENCODERS MONITOR TAB Figure 4-12 : WebEASY – Encoders Monitor Tab ® Video Monitor Video Status: This parameter displays the detected video resolution of the encoder. Audio Monitor Audio Status: This parameter displays audio channel pairs that are present at the input. It monitors the audio control packets.

  • Page 36: Preset Tab

    Preset Name: This field allows the user to enter a name for each preset. Preset Store: This control will take the current 7882J2KX-IPASI settings and save them to a Preset. When storing a preset, all parameters will be stored except the following: •...

  • Page 37: System Notify Tab

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder 4.10. SYSTEM NOTIFY TAB Figure 4-14 : WebEASY – System Notify Tab ® Temperature Control Temperature Monitor 1: This field displays the module’s temperature. System Notification Fan Status: This control sends out a trap if there is a fault generated by the Fan when enabled.

  • Page 38: Encoder Notify Tab

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder 4.11. ENCODER NOTIFY TAB Figure 4-15 : WebEASY – Encoder Notify Tab ® Video Monitoring Control Black Duration: This control allows the user to set the duration, in frames of active picture content below 7 IRE that is considered a fault. This parameter is adjusted in four-frame increments. As in 1 = 4 frames and 10 = 40 frames.

  • Page 39: 4.12. Decoder Notify Tab

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder Encoder Input Status: This control sends out a trap if there is a fault generated by the Encoder Input Status when enabled. This reports the input video status. If no input is provided, this fault will be active.
  • Page 40 7882J2KX-IPASI Single Channel J2K Encoder/Decoder This page left intentionally blank Page - 30 Revision 1.0...

  • Page 41: Vistalink Pro Interface

    ® network administrator has already added the appropriate jar file to the server, and both the client and server applications have been restarted There are two methods that can be used to communicate with the 7882J2KX-IPASI and VistaLINK ® PRO.

  • Page 42: System Tab

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder 5.1. SYSTEM TAB Figure 5-1 : VistaLINK - System Tab Part 1 ®  Note: For IP address settings on Control and Data ports, after applying any changes, the device must be rebooted for the changes to take effect. Reboot can be pressed at the bottom of this System tab after all changes are made.
  • Page 43 Syslog is a valuable tool for debugging the device operation. It is essentially serial readouts over IP, sent to a dedicated server. If issues are present Evertz can help install and setup a syslog server for constant monitoring of the device activity.

  • Page 44: Figure 5-2 : Vistalink

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder Figure 5-2 : VistaLINK - System Tab Part 2 ® SNMP Trap Destinations There are 10 trap destinations that can be configured and enabled. Destination Enable: This control is used to enable or disable sending out traps.

  • Page 45: Product Features

    Single Channel J2K Encoder/Decoder 5.2. PRODUCT FEATURES The 7882J2KX-IPASI has the ability to enable features by adding/updating applicable licenses. Please contact Evertz Microsystems Ltd for any additional License generation along with Product Serial Number and Product MAC address. Figure 5-3 : VistaLINK - Product Features Tab ®...
  • Page 46 The 7882J2KX-IPASI supports 1 encoder and 1 decoder by default. Product License Product Serial Number: This parameter displays the card serial number. This is required by Evertz when generating or updating license files on the 7882J2KX-IPASI. Product MAC Address: This parameter displays the card MAC address. This is required by Evertz when generating or updating license files on the 7882J2KX-IPASI.

  • Page 47: Decoder Control

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder 5.3. DECODER CONTROL Figure 5-4 : VistaLINK - Decoder Control Tab (Part 1) ® Output Control Force Interface: This is an engineering control. Please leave it configured to the default setting. Loss of Video Output: This control allows the user to select the decoder output on a loss of video output.
  • Page 48 7882J2KX-IPASI Single Channel J2K Encoder/Decoder Input Program Control Program Tuning Mode: Options are Auto PID Select or Manual PID Select. o Selection of Auto PID Select will set the decoder to decode either the  First Program In The PAT ...

  • Page 49: Figure 5-5 : Vistalink

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder Figure 5-5 : VistaLINK - Decoder Control Tab (Part 2) ® IGMPV3 SSM Profile Control For Main and Backup: IGMP Source 1 to 6: The user can add the required SSM sources for V3. Switch Over Control User Redundancy Mode: This control is used to enable redundancy mode for switch over on a loss input.

  • Page 50: Decoder Audio Control Tab

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder 5.4. DECODER AUDIO CONTROL TAB Figure 5-6 : VistaLINK - Decoder Audio Control Tab ® Audio Input Control For Audio 1-4: PID Select: This control is used to select the audio PID to use for decoding.

  • Page 51: Decoder Monitor Tab

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder 5.5. DECODER MONITOR TAB Figure 5-7 : VistaLINK - Decoder Monitor Tab ® Page - 41 Revision 1.0...
  • Page 52 7882J2KX-IPASI Single Channel J2K Encoder/Decoder Input Monitor Status: This field displays if an input is detected on the decoder. Bitrate: This field displays the detected bitrate for the input. Input Packet Framing: This field displays the type of packet framing detected. Options are RTP or UDP.

  • Page 53: Input Audio Proc Control

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder 5.6. INPUT AUDIO PROC CONTROL Figure 5-8 : VistaLINK - Input Audio Proc Control Tab ® Input Audio Proc Control Enable Audio Proc: If this is disabled, Audio will follow the embedded audio. If this parameter is enabled, it allows the user to select which incoming embedded audio channel goes to which Encoder source channel.

  • Page 54: Encoders Control Tab

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder 5.7. ENCODERS CONTROL TAB Figure 5-9 : VistaLINK - Encoders Control Tab Part 1 ® Output Configuration IP Address: This parameter allows the user to select a streaming output IP address for the Encoder. It can be a Multicast or Unicast address.

  • Page 55: Figure 5-10 : Vistalink

    Figure 5-10 : VistaLINK - Encoders Control Tab Part 2 ® Audio PID Assignment Audio 1 to 4 PID: The 7882J2KX-IPASI has 4 x Audio Pids. These parameters allow the user to select the Audio PID number. Page - 45 Revision 1.0...

  • Page 56: Encoders Monitor Tab

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder Audio MUX Control For Audio 1 to 4: First AES On Output: This parameter allows the user to select the de-embedded audio pair on the audio encoder. Total AES On Output: This parameter allows the user to set the number of AES pair on a certain PID.

  • Page 57: Preset Tab

    Preset Name: This field allows the user to enter a name for each preset. Preset Store: This control will take the current 7882J2KX-IPASI settings and save them to a Preset. When storing a preset all parameters will be stored except the following: •...

  • Page 58: System Notify Tab

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder 5.10. SYSTEM NOTIFY TAB Figure 5-13 : VistaLINK - System Notify Tab ® Temperature Control Temperature Monitor 1: This field displays the module’s temperature. System Notification Fan Status: This control sends out a trap if there is a fault generated by the Fan when enabled.

  • Page 59: Encoder Notify Tab

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder SFP 2 External Link: This control sends out a trap if there is a fault generated by a link loss on SFP 2 when enabled. SFP External Link Fault Present monitor displays if there is a fault condition on the SFP 2.

  • Page 60: 5.12. Decoders Notify Tab

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder default a grey test pattern is generated when input video is removed. Hence the video presence will still be active. Video Faults display if there is a fault condition on the Video Present. Green indicates healthy while red indicates a fault.
  • Page 61 7882J2KX-IPASI Single Channel J2K Encoder/Decoder Decoder Input Faults displays if there is a fault condition on the TS Sync Byte Missing. Green indicates healthy while red indicates a fault. Video PID Missing: This control sends out a trap if there is a fault generated by a missing Video PID when enabled.
  • Page 62 7882J2KX-IPASI Single Channel J2K Encoder/Decoder This page left intentionally blank Page - 52 Revision 1.0...

  • Page 63: Upgrade Procedures

    6.1. UPDATING VLPRO SERVER JAR FILE Products from Evertz are constantly evolving and new features are often added. It is therefore important to update the JAR files in use to provide access to all the latest features or enhancements. It will also be necessary to add JAR files for new products.

  • Page 64: Figure 6-2 : Vistalink

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder A window will appear, as shown in Figure 6-2. Navigate to the location of the new JAR file and double click to select the file. The window will automatically close and the update will be applied in the background.

  • Page 65: Firmware Upgrade

    Password. Enter “customer” for Login and “customer” for Password. On the top of the web page for the 7882J2KX-IPASI, there is a tab labeled Upgrade. The Upgrade tab is used to check current firmware version and upload the latest firmware.

  • Page 66: Figure 6-4 : Webeasy - Firmware Upgrade Menu

    7882J2KX-IPASI Single Channel J2K Encoder/Decoder Figure 6-4 : WebEASY - Firmware Upgrade Menu ® Click Choose File and browse to locate image file. Once selected, click Open to advance to next step. Click Upgrade and watch progress bar for status. Once completed, the device will automatically restart.

  • Page 67: Firmware Upgrade Using Vistalink

    7882J2KX-IPASI or using the 7800FC frame controller. Both methods use the same procedure. Ensure that the 7882J2KX-IPASI is running the latest firmware, to check this simply right click on the cards address in VLPro Client and select Version Information as shown in Figure 6-6.

  • Page 68: Figure 6-7 : Vistalink

    10 minutes depending on network traffic. The progress bar to the right will provide feedback on the status of the upgrade. Figure 6-8 : Selecting File for Firmware Upgrade • Upon completion, the 7882J2KX-IPASI module will reboot automatically and return online in normal “run” mode. Page - 58 Revision 1.0...

Table of Contents