GDC Espedeo Supra Supra-5000 User Manual page 171

90001
DCMB The ddp2 color wheel failure.
The ddp2 rotation speed of the
90002
DCMB
color wheel is too low.
The ddp2 rotation speed of the
90003 DCMB
color wheel is too high.
The ddp2 system module
91001
DCMB
initialization failure.
The ddp2 system monitor
91002
DCMB
initialization failure.
The ddp2 circuit initialization
91003 DCMB
The ddp2 color wheel
91004
DCMB
sequence failure.
The ddp2 DMD initialization
91005
DCMB
The ddp2 DMD/ASIC
91006
DCMB
incompatibility failure.
The ddp2 Current DCP does
91007
DCMB
not support 6: 2 frame rate.
92001 DCMB The ddp2 DAD2000 failure.
92002
DCMB The ddp2 EEPROM failure.
The ddp2 serial
93001
DCMB
communication failure.
Light
20000
Undefined alarm and error.
Source
Light The phosphor motor internal
20001
Source rotation speed_Low.
Light The phosphor motor internal
20002
Source rotation speed_Too low.
Light The phosphor motor internal
20003
Source rotation speed_High.
Supra-5000 Digital Cinema and Secured Media Projection System
User Manual
The color wheel is functioning
abnormally.
The rotation speed of the color wheel
is too low.
The rotation speed of the color wheel
is too high.
The system module initialization has
failed.
The system monitoring module
initialization has failed.
The ddp2 circuit initialization has
failure. failed.
The color wheel could not be
enabled.
The DMD initialization has failed.
failure.
The DMD does not match the
system.
The current DCP only supports 4: 2
frame rate.
The DAD2000 could not be enabled.
The EEPROM read/write operation is
abnormal.
The ddp2 failed to communicate with
the PIB board.
1. The phosphor motor drive of the
PIB board is faulty.
2. The phosphor motor is faulty.
1. The phosphor motor drive of the
PIB board is faulty.
2. The cable is not properly
connected.
3. The phosphor motor is faulty.
1. The phosphor motor drive of the
PIB board is faulty.
2. The phosphor motor is faulty.
1. Check whether the color wheel drive cable (J42) on
the DCMB and the color wheel feedback cable (J31) on
the backplane are loose.
2. Check whether the diffusor wheel module of the light
source (color wheel adapter board connection cable and
diffusor wheel motor speed) is functioning properly.
3. Restart the projector.
Check whether the color wheel model matches the
system or the color wheel is abnormal.
Check whether the color wheel model matches the
system or the color wheel is abnormal.
Restart the projector or replace the DCMB board.
Restart the projector or replace the DCMB board.
Restart the projector or replace the DCMB board.
Check whether the color wheel drive cable (J42) on the
DCMB and the color wheel feedback cable (J31) on the
backplane are loose.
Check whether the DCMB ddp2 DMD flat cable (J45 and
J46) is loose.
Check whether the DCMB ddp2 DMD model or software
matches the system.
The projector has automatically corrected the 3D frame
rate to 4: 2.
Check the DCMB ddp2 DMD flat cable (J45 and J46) or
restart the projector.
1. Check whether the DMD control firmware version
is correct.
2. Replace the DCMB board.
1. Restart the projector
2. Check whether the flat cable (J47) from the backplane
(CON2) to the DCMB board is loose or replace the flat
cable.
3. Replace the PIB board.
1. Replace the PIB board.
2. Replace the light engine (phosphor motor).
1. Replace the PIB board.
2. Replace the cable between the backplane and the
color wheel adapter board.
3. Replace the light engine (phosphor motor).
1. Replace the PIB board.
2. Replace the light engine (phosphor motor).
- 171 -
th
May 05 , 2021