Binding Receivers - GRAUPNER MC-20 HoTT Programming Manual

Another tap on the SET key will again deactivate
option selection so a change to another line can be
affected.
Module
B A S I C S E T T I N G , M O D E L
Model name Starlet
Info 1234g/111111
Stick mode
Module HoTT bind n/a
SEL BD1 BD2 BD3 BD4
mc-20
The transmitter has a HoTT RF module as
standard equipment. In addition to the built-in module,
there is a connector for an external RF module
behind one of the two front cover fl aps (see page 25)
and a switchover to an external module connected
there can be affected per software. To do this, use the
selection keys of the left or right touch pad to move
the marker frame left to the "Module" selection fi eld
above the "SEL" column label.
HoTT system
Graupner HoTT receivers must be "instructed"
to communicate exclusively with a certain model
(memory) in a Graupner HoTT transmitter. This
procedure is known as "binding" and must only be
done once for every new receiver/model-memory-
location combination (and can be repeated anytime).
Important notices:
• During the binding procedure be sure the
transmitter's antenna is always far enough
away from the receiver's antenna. To be on the
safe side, keep them at least one meter apart.
Otherwise there is a risk of a faulty connection
to the return channel and malfunctions will
result.
• When binding additional receivers, note that any
other –switched on– receivers already bound
to the transmitter will fall into Fail-safe mode
during the transmitter-side "binding" period.
"Binding" multiple receivers per model
Multiple receivers per model can be bound if desired,
whereby respective
potential for managing up to four receivers directly
and for dividing up the transmitter's 16 control
1
channels (max) in any arrangement among these
n/a n/a
receivers under menu control. Refer to additional
details further down in this section. First bind the
receivers individually as described below.
However, in subsequent operation only one of
these receivers will establish a telemetry bond to
the transmitter; the one which was activated in
the "TELEMETRY RCV" line of the »Telemetry«
menu, for example:
TELEMETRY
TELEMETRY RCV
SETTING & DATAVIEW
SENSOR SELECT
RF STATUS VIEW
VOICE TRIGGER
Any telemetry sensors which may be built into the
model should therefore be connected to this receiver
because the transmitter only receives and evaluates
data from the return channel of the receiver activated on
this line. The second, and all other receivers, operate in
parallel but are fully independent in slave mode.
"Binding" transmitter and receiver
Use the selection keys of the left or right touch
pad to move into the "Module" line. The marker frame
will be positioned by default to the column for the next
free binding channel. In the example shown in the
mc-20
HoTT programs offer the
BIND. 1
Detail program description - Base setup models | Winged models
fi gure below, the marker frame is positioned above the
column label "BD2" because the binding channel in the
column labeled "BD1" is already in use by default for
the receiver which was delivered with the set.
B A S I C S E T T I N G , M O D E L
Model name Starlet
Info 1234g/111111
Stick mode
Module HoTT bind n/a
SEL
BD1 BD2 BD3 BD4
If not already off, now switch the receiver on. The red
LED on the receiver will blink.
Press and hold the SET button on the receiver while
the LED continues to blink red for about 3 seconds
then, after about another 3 seconds, begins to blink
red/green. The SET button on the receiver can now
be released. As long as this LED blinks red/green, the
receiver is in bind mode.
Now, within this 3 second period, start the so-called
"receiver binding" process for the receiver to the
currently active model memory with a brief tap on the
center SET key of the right touch pad. At this time,
the screen's display will blend in a message window
for the duration of the "binding" process.
B A S I C S E T T I N G , M O D E L
Model name Starlet
FINDING...
Info 1234g/111111
Stick mode
Module HoTT bind n/a
SEL BD1 BD2 BD3 BD4
If the receiver's LED, again blinking red, changes
within about 10 seconds to continuous illumination
in green, the binding process has been successfully
1
n/a n/a
1
n/a n/a
85