GRAUPNER MC-20 HoTT Programming Manual page 235

OUTPUT CH 3: Right horizontal/vertical
If the servo's direction of rotation is incorrect,
please observe the notices on page 62.
RX CURVE (EXPO)
TELEMETRY
RX CURVE
CURVE1 CH : 02
TELEMETRI RCV
TYPE :
SETTING & DATAVIEW
CURVE2 CH : 03
TYPE :
SENSOR SELECT
CURVE3 CH : 04
RF STATUS VIEW
TYPE :
VOICE TRIGGER
Value Explanation Possible settings
CURVE1, Channel 1 ... depending on
2 or 3 CH assignment of the receiver
respective curve
setting
TYPE Curve type A, B, C
see fi gure
TYPE A
Expo = –100% TYPE B
DR = 125% linear
–100% 0 +100% –100% 0 +100%
Control travel Control travel
Normally a non-linear control function, if applicable, is
used for the aileron (channel 2), elevator (channel 3)
and rudder (channel 4). These channel defaults also
correspond to the factory settings. BUT CAUTION:
This assignment only applies when, on the transmitter
side, neither "2HRSv3+8" is specifi ed in the "Tail
type" line nor is "2AIL" or 2AIL 2FL" specifi ed in the
"Aileron/camber fl aps" line of the »Base settings«
menu. Otherwise, assignments will have already
been made in the transmitter for control function 3
(elevator), which will then be split between control
channels 3 & 8, or control function 2 (aileron), which
will then be split between control channels 2 & 5 for
the left and right ailerons. The corresponding control
channels (INPUT CH) in the receiver would in both
BIND. 1
cases be channels 03 & 08 or 02 & 05.
B
Therefore if, for example, "2AIL" has been specifi ed
B
on the transmitter side and the intent here is to utilize
the RX CURVE option instead of the
B
transmitter's individually adjustable »Dual Rate /
Expo« menu (see page 120 or 124), then two curves
must be set:
TELEMETRY
TELEMETRI RCV
SETTING & DATAVIEW
SENSOR SELECT
RF STATUS VIEW
VOICE TRIGGER
TYPE C
Expo = +100%
Otherwise, the left and right ailerons have different
DR = 70%
control characteristics.
With the RX CURVE function you can manage the
control characteristics for up to three servos:
• CURVE 1, 2 or 3 CH
Select the desired control channel (INPUT CH) of
the fi rst servo.
–100% 0 +100% The following setting in TYPE only pertains to the
Control travel
channel selected here.
TYPE
Select the servo curve:
A: EXPO = -100 % and DUAL RATE = 125 %
The servo reacts strongly to movements of the
joystick around the neutral position. As the rudder
throw increases, the curve becomes fl atter.
mc-20
RX CURVE
CURVE1 CH : 02 BIND. 1
TYPE : B
CURVE2 CH : 05
TYPE : B
CURVE3 CH : 04
TYPE : B
B: Linear setting.
The servo follows the joystick movement linearly.
C: EXPO = +100 % and DUAL RATE = 70 %
The servo reacts weakly to the joystick
movements around the neutral position. As the
rudder throw increases, the curve becomes
steeper.
Note:
The control characteristics programmed here also
affect the mapped receiver outputs.
HoTT
5CH FUNCTION: "SERVO" or "SENSOR"
TELEMETRY
RX CURVE
CURVE1 CH
TELEMETRI RCV
TYPE :
SETTING & DATAVIEW
CURVE2 CH
TYPE :
SENSOR SELECT
CURVE3 CH
RF STATUS VIEW
TYPE :
5CH FUNCTION:SERVO
VOICE TRIGGER
Some receivers have a specifi c servo connection
which has been made switchable rather than an
independent telemetry connection. Thus, for example,
on the GR-12 receiver included with the mx-12 HoTT
set, order no. 33112, , servo connector 5 has an extra
"T" mark and can be alternatively connected ...
... not only via an order no.
to upgrade the receiver
telemetry sensor.
However, in order for the receiver to correctly
recognize the given connected device correctly, servo
connection 5 (in this case) MUST be appropriately set
Detail program description - Telemetry
: 02
BIND. 1
A
: 03
A
: 04
B
Servo
OR
Sensor
7168.6Aadaper cable
but also connected to a
235