GRAUPNER MC-20 HoTT Programming Manual page 125

Roll ––– 100% ––– 0%
Pitch ax ––– 100% ––– 0%
Move desired switch
Tail rot – 100% ––– 0%
to ON position
EXPO
(ext. switch: ENTER) DUAL
Normal
SEL SEL
If necessary, this may also be one of the transmitter
control switches C1 ... C8 or C1i ... C8i or one of the
logical switches L1 ... L8 or L1i ... L8i from the list of
"expanded switches".
The switch so assigned appears on the display,
together with a switch icon that indicates the switch's
switching direction.
In the case of "C" or "L" switches, the joystick or
another transmitter control or a certain switching
logic can itself be used as a switch. However, such a
control switch must have been appropriately defi ned
in the »Control switch« menu, see page 119, and a
logical switch must have been appropriately defi ned
in the »Logical switch« menu, see page 138.
Whichever switch has been assigned ... the
respective switch will appear in the display together
with a switch symbol indicating the switch's direction
if actuated, e.g. in the «Normal» fl ight phase.
Roll 3 100% ––– 0%
Pitch ax ––– 100% ––– 0%
Tail rot ––– 100% ––– 0%
DUAL EXPO
Normal
SEL SEL
Once the value fi eld has been activated with a brief
tap on the SET key of the right touch pad, use the
selection keys of the left or right touch pad to move
into the Dual-Rate value column labeled SEL at the
bottom edge of the display in order to separately
change the dual-rate values shown in inverse video
for each of the two switch positions.
Roll 3 111% ––– 0%
100%
Pitch ax ––– ––– 0%
Tail rot ––– 100% ––– 0%
DUAL EXPO
Normal
SEL SEL
Roll 3 88% ––– 0%
Pitch ax ––– 100% ––– 0%
Tail rot ––– 100% ––– 0%
EXPO
DUAL
Normal
SEL SEL
At the same time, the Dual-Rate curve will be
presented in the graph. A simultaneous tap on the
or keys of the right touch pad (CLEAR) will
reset a changed entry fi eld value displayed in inverse
video back to "100 %".
Caution:
For safety reasons, Dual Rate value settings should
not be less than 20 %.
Some examples of Dual Rate values:
Dual Rate = 100% Dual Rate = 50%
Stick deflection Stick deflection
Exponential function
If a switchover between two variants is desired,
assign a switch in the column labeled with the
switch symbol (as described in the section "Assigning
transmitter controls, switches and control switches"
on page 56).
Roll 3 100%
Pitch ax ––– 100%
Move desired switch
Tail rot ––– 100%
to ON position
(ext. switch: ENTER) DUAL
Normal
If necessary, this may also be one of the transmitter
control switches C1 ... C8 or C1i ... C8i or one of the
logical switches L1 ... L8 or L1i ... L8i from the list of
"expanded switches".
The switch so assigned appears on the display,
together with a switch icon that indicates the switch's
switching direction.
In the case of "C" or "L" switches, the joystick or
another transmitter control or a certain switching
logic can itself be used as a switch. However, such a
control switch must have been appropriately defi ned
in the »Control switch« menu, see page 119, and a
logical switch must have been appropriately defi ned
in the »Logical switch« menu, see page 138.
Whichever switch has been assigned ... the
respective switch appears on the display together
Dual Rate = 20%
with a switch icon that indicates the switch's
respective direction when moved.
Stick deflection
Detail program description - Dual Rate / Expo | Helicopters
––– 0%
––– 0%
––– 0%
EXPO
SEL SEL
125