Table of Contents
Advertisement
SuperServer 6029TP-HTR/HC0R/HC1R User's Manual
Server ME (Management Engine) Configuration
This feature displays the following system ME configuration settings.
General ME Configuration
Operational Firmware Version
Backup Firmware Version
Recovery Firmware Version
ME Firmware Status #1/ME Firmware Status #2
Current State
Error Code
PCH SATA Configuration
When this submenu is selected, the AMI BIOS automatically detects the presence of the SATA
devices that are supported by the Intel PCH chip and displays the following items:
SATA Controller
This item enables or disables the onboard SATA controller supported by the Intel PCH chip.
The options are Enable and Disable.
Configure SATA as (Available when the item above: SATA Controller is set to
enabled)
Select AHCI to configure a SATA drive specified by the user as an AHCI drive. Select RAID
to configure a SATA drive specified by the user as a RAID drive. The options are AHCI and
RAID. (Note: This item is hidden when the SATA Controller item is set to Disabled.)
SATA HDD Unlock
Select Enable to unlock SATA HDD password in the OS. The options are Enable and Disable.
SATA/sSATA RAID Boot Select (Available when the item "Configure SATA as" is set
to "RAID")
This feature allows the user to decide which controller should be used for system boot. The
options are None, SATA Controller, sSATA Controller, and Both.
Aggressive Link Power Management
When this item is set to Enabled, the SATA AHCI controller manages the power use of the
SATA link. The controller will put the link in a low power mode during an extended period of
I/O inactivity, and will return the link to an active state when I/O activity resumes. The options
are Enable and Disable.
84
SATA RAID Option ROM/UEFI Driver (Available when the item "Configure SATA as"
is set to "RAID")
Select EFI to load the EFI driver for system boot. Select Legacy to load a legacy driver for
system boot. The options are Disable, EFI, and Legacy.
SATA Port 0 - SATA Port 7
Hot Plug
Select Enable to support Hot-plugging for the device installed on a selected SATA port
which will allow the user to replace the device installed in the slot without shutting down
the system. The options are Enable and Disable.
Spin Up Device
On an edge detect from 0 to 1, set this item to allow the SATA device installed on the SATA
port specified by the user to start a COMRESET initialization. The options are Enable and
Disable.
SATA Device Type
Use this item to specify if the device installed on the SATA port selected by the user should
be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk Drive
and Solid State Drive.
PCH sSATA Configuration
When this submenu is selected, AMI BIOS automatically detects the presence of the sSATA
devices that are supported by the PCH sSATA controller and displays the following items:
sSATA Controller
This item enables or disables the onboard sSATA controller supported by the Intel SCU. The
options are Enable and Disable.
Configure sSATA as
Select AHCI to configure an sSATA drive specified by the user as an AHCI drive. Select RAID
to configure an sSATA drive specified by the user as a RAID drive. The options are AHCI
and RAID. (Note: This item is hidden when the sSATA Controller item is set to Disabled.)
SATA HDD Unlock
Select Enable to unlock sSATA HDD password in the OS. The options are Enable and Disable.
SATA/sSATA RAID Boot Select (Available when the item "Configure SATA as" is set
to "RAID")
This feature allows the user to decide which controller should be used for system boot. The
options are None, SATA Controller, sSATA Controller, and Both.
85
Chapter 4: BIOS
Advertisement
Table of Contents
