Table of Contents
Advertisement
SuperServer 6029TP-HTR/HC0R/HC1R User's Manual
DIMM
1 x4 DIMM
Must be installed on iMC0 DDR Channel 0
Population
within an IMC
Note:
2 x4 DIMMs
DDR0: Populate with 1 DIMM
Uniformly
DDR1: Populate identically as DDR0
populate with
x4 DRAMs/
3 x4 DIMMs
DDR0: Populate with 1 DIMM
DIMMs
DDR1: Populate identically as DDR0
DDR2: Populate identically as DDR1
4 x4 DIMMs
DDR0: Populate with 2 DIMMs
DDR1: Populate identically as DDR0
5 x4 DIMMs
DDR Channel 0, 1, 2: DIMM0 is populated with identical DIMMs,
DDR Channel 0, 1: DIMM1 is populated with identical DIMMs
6 x4 DIMMs
Populate 2 DIMMs per DDR channel
DIMM
1 pair of
DDR0: Populate with 1 DIMM
Population
DIMMs
DDR1: Populate the second DIMM (for best performance)
within an IMC
2 pairs of
DDR0: Populate with 1 pair of non-equal rank DIMMs
Note: Non-
DIMMs
DDR1: Populate identically as DDR0
equal in rank
3 pairs of
DDR0: Populate with 1 pair of non-equal rank DIMMs
pair of x4
DIMMs
DDR1: Populate identically as DDR0
DIMMs)
DDR2: Populate identically as DDR1
2 pairs+1
DDR0: Populate with 1 pair of non-equal rank DIMMs
(5DIMMs)
DDR1: Populate with identical DIMMs as DDR0
DDR2: DIMM0 is populated with identical DIMM as DDR1
DIMM
1 pair of x8, x4
DDR0: Populate with 1 DIMM
Population
DDR1: Populate the second DIMM (for best performance)
within an IMC
2 pairs of x8, x4
Populate with 1 pair of DIMMs on DDR0, and identical pair on DDR1
3 pairs of x8, x4
A pair of DIMMs on DDR0, and identical pair on DDR1, and DDR2
42
1
Y, only Bank
VLS
>1
Y
1
Y, only Bank
VLS
>1
Y
1
Y, only Bank
VLS
>1
Y
x
Y
>1
Y
x
Y
>1
Y
>1
Y
x
Y
>1
Y
No
No
No
Caution: Exercise extreme caution when installing or removing memory modules to prevent
any possible damage to the DIMMs or slots.
Warning: In dual-CPU configurations, memory must be installed in the DIMM slots associated
with the installed CPUs.
Chapter 3: Maintenance and Component Installation
Memory Installation
Memory Support
The X11DPT-PS supports up to up to 1024 GB of Load Reduced DIMM (LRDIMM), Registered
DIMM (RDIMM), Non-Volatile DIMM (NV-DIMM) DDR4 (288-pin) ECC modules in 16 slots
memory slots. Populating two adjacent slots at a time with memory modules of the same
size and type will result in interleaved (128-bit) memory, which is faster than non-interleaved
(64-bit) memory.
Check the Supermicro website for possible updates to memory support.
Installing Memory
Begin by removing power from the system as described in Section 3.1.
1. Insert DIMM modules in the following
order: P1-DIMMA1, P1-DIMMB1, P1-
DIMMC1, P1-DIMMD1, P1-DIMME1, P1-
DIMMF1 then P1-DIMMA2, P1-DIMMD2.
For the system to work properly, please
use memory modules of the same type
and speed on the motherboard.
2. Push the release tabs outwards on both
ends of the DIMM slot to unlock it.
3. Align the key of the DIMM module with
the receptive point on the memory slot.
4. Align the notches on both ends of the
module against the receptive points on
the ends of the slot.
5. Use two thumbs together to press the
notches on both ends of the module
straight down into the slot until the
module snaps into place.
6. Press the release tabs to the lock
positions to secure the DIMM module
into the slot.
43
Notches
BIOS
LICENSE
X11DPT-PS
Rev. 1.02
Release Tabs
Press both notches
straight down into
the memory slot.
Advertisement
Table of Contents
