Table of Contents
Advertisement
SuperServer 6029TP-HTR/HC0R/HC1R User's Manual
Attaching the F-Model Processor to the Narrow Processor Clip to Create
the Processor Package Assembly
To properly install the CPU into the narrow processor clip, please follow the steps below.
1. Locate pin 1 (notch A), which is the triangle located on the top of the narrow processor
clip. Also locate notch B and notch C on the processor clip.
2. Locate pin 1 (notch A), which is the triangle on the substrate of the CPU. Also, locate
notch B and notch C on the CPU as shown below.
3. Align pin 1 (the triangle on the substrate) of the CPU with pin 1 (the triangle) of
the narrow processor clip. Once they are aligned, carefully insert the CPU into the
processor clip by sliding notch B of the CPU into notch B of the processor clip, and
sliding notch C of the CPU into notch C of the processor clip.
4. Examine all corners of the CPU to ensure that it is properly seated on the processor
clip. Once the CPU is securely attached to the processor clip, the processor package
assembly is created.
Note: Please exercise extreme caution when handling the CPU. Do not touch the CPU
LGA-lands to avoid damaging the LGA-lands or the CPU. Be sure to wear ESD gloves when
handling components.
D
CPU (Upside Down)
Align Notch D of the CPU
w/CPU LGA Lands up
and Notch D of the Processor Clip
C
B
A
Align Notch C of the CPU
Pin 1
and Notch C of the Processor Clip
Align Notch B of the CPU
C
and Notch B of the Processor Clip
B
CPU/Heatsink Package
(Upside Down)
Align CPU Pin 1
A
Processor Package Carrier (w/CPU mounted on the
Processor Clip)
32
D
Allow Notch D to
latch on to CPU
D
B
Allow Notch C to
latch on to CPU
Allow Notch B to
A
latch on to CPU
Chapter 3: Maintenance and Component Installation
Attaching the Non-F Model Processor Package Assembly to the Heatsink to
Form the Processor Heatsink Module (PHM)
After you have made a processor package assembly by following the instructions on the
previous page, please follow the steps below to mount the processor package assembly onto
the heatsink to create the Processor Heatsink Module (PHM).
1. Locate "1" on the heatsink label and the triangular corner next to it on the heatsink.
With your index finger pressing against the screw at this triangular corner, carefully hold
and turn the heatsink upside down with the thermal-grease side facing up. Remove the
protective thermal film if present, and apply the proper amount of the thermal grease
as needed. (Skip this step if you have a new heatsink because the necessary thermal
grease is pre-applied in the factory.)
2. Holding the processor package assembly at the center edge, turn it upside down. With
the thermal-grease side facing up, locate the hollow triangle located at the corner of the
processor carrier assembly ("a" in the graphic). Note a larger hole and plastic mounting
clicks located next to the hollow triangle. Also locate another set of mounting clicks and
a larger hole at the diagonal corner of the same (reverse) side of the processor carrier
assembly ("b" in the graphic).
3. With the back of heatsink and
the reverse side of the processor
package assembly facing up, align
the triangular corner on the heatsink
("A" in the graphic) against the
Triangle on the CPU
mounting clips next to the hollow
triangle ("a") on the processor
package assembly.
4. Also align the triangular corner ("B")
at the diagonal side of the heatsink
Triangle on the
Processor Clip
with the corresponding clips on the
processor package assembly ("b").
5. Once the mounting clips on the
processor package assembly
are properly aligned with the
corresponding holes on the back
of heatsink, securely attach the
heatsink to the processor package
assembly by snapping the mounting
clips at the proper places on the
heatsink to create the processor
heatsink module (PHM).
33
Non-Fabric CPU and Processor Clip
(Upside Down)
b
c
d
B
a
C
D
Heatsink
A
(Upside Down)
On Locations of (C, D),
the notches
snap onto the heat sink's
B
mounting holes
C
D
A
On Locations (A, B), the notches
Make sure Mounting
snap onto the heatsink's sides
Notches snap into place
Advertisement
Table of Contents
