Table of Contents
Advertisement
Item
[TYPE C FULL]
[TYPE C NEAR END]
[TYPE C END]
[BATT STAT NEAR END]
[BATT STAT END]
[ENDURA STAT NEAR END]
[ENDURA STAT END]
[FILE]
These are items for performing file-related operations such as reading from an SD memory card containing menu settings data, and handling lens files
and lens chromatic aberration correction (CAC) files.
These menu items cannot be set when the thumbnail screen is displayed or during playback.
[FILE] menu cannot be operated in the following cases:
f While the thumbnail screen is displayed
Remedy: Press the <THUMBNAIL> button to close the thumbnail screen, and try the operations again.
f During playback
Remedy: Press the <STOP> button to stop playback, and try the operations again.
f When recording by linking to the previous clip is possible in one-clip recording mode (when [1*CLIP] is displayed at the bottom right in the viewfinder
and the LCD monitor)
Remedy: Close the menu once, and hold down the <STOP> button for approx. 2 seconds to end linking of clips, and then try the operation again.
f During standby in interval recording or one-shot recording
Remedy: Press the <STOP> button to end interval recording, and try the operation again.
[SETUP DATA (SD CARD)]
Item
[LOAD]
[SAVE]
[SAVE AS]
[SETUP DATA SELECT]
f Select menu items to save to/read from to SD memory card in the main menu → [FILE] → [SETUP DATA (SD CARD)].
f The factory settings are as follows:
Chapter 6 Menu Operations — Menu list
Selects the voltage for full display in steps of 0.1 V when the main menu → [I/F SETUP] → [BATTERY/
P2CARD] → [BATTERY SELECT] is set to [TYPE C].
[13.0V]...[17.0V]
f Factory setting: [15.9V]
Selects the near end voltage in steps of 0.1 V when the main menu → [I/F SETUP] → [BATTERY/
P2CARD] → [BATTERY SELECT] is set to [TYPE C].
[11.0V]...[15.0V]
f Factory setting: [13.2V]
Selects the end voltage in steps of 0.1 V when the main menu → [I/F SETUP] → [BATTERY/P2CARD] →
[BATTERY SELECT] is set to [TYPE C].
[11.0V]...[15.0V]
f Factory setting: [12.5V]
Selects the near end percent value.
[4%], [5%], [6%], [7%], [8%], [9%], [10%], [12%], [14%], [16%], [18%], [20%]
f Factory setting: [5%]
When the battery charge level percentage cannot be detected, this will follow the near end voltage value
set in [TYPE A].
If a battery is used for which the remaining charge is displayed in units of 10%, the setting value and actual
near end warning may vary slightly.
Selects the end percent value.
[1%]...[10%]
f Factory setting: [1%]
When the battery charge level percentage cannot be detected, this will follow the end voltage value set in
[TYPE A].
When using a battery which displays battery charge level by units of 10%, end is determined only in two
stages: when it is set between [1%] and [5%], or when it is set between [6%] to [10%].
Selects the near end percent value.
[4%], [5%], [6%], [7%], [8%], [9%], [10%], [12%], [14%], [16%], [18%], [20%]
f Factory setting: [5%]
When the battery charge level percentage cannot be detected, this will follow the near end voltage value
set in [TYPE A].
If a battery is used for which the remaining charge is displayed in units of 10%, the setting value and actual
near end warning may vary slightly.
Selects the end percent value.
[1%]...[10%]
f Factory setting: [1%]
When the battery charge level percentage cannot be detected, this will follow the end voltage value set in
[TYPE A].
When using a battery which displays battery charge level by units of 10%, end is determined only in two
stages: when it is set between [1%] and [5%], or when it is set between [6%] to [10%].
Loads the file selected from the setup data file list saved to the SD memory card to the camera.
The data selected in [SETUP DATA SELECT] is loaded.
Overwrites the current menu setting values in the camera to the file selected from the existing file list
saved to the SD memory card.
Data selected in [SETUP DATA SELECT] is saved.
Enters the current menu setting values of the camera to file name and title as a new file and saves it to the
SD memory card.
Data selected in [SETUP DATA SELECT] is saved.
– 192 –
Description of settings
Description of settings
Advertisement
Table of Contents
