Table of Contents
Advertisement
[REC/PB SETUP]
Item
[REC MEDIA]
[FILE SPLIT]
[START TEXT MEMO]
[P.ON REC SLOT SEL]
[REC START]
[REC TALLY]
[ACCESS LED]
[SEEK POS SEL]
Chapter 6 Menu Operations — Menu list
Selects the slot for the media to be recorded.
[P2]: Uses P2 memory cards (slots 1 and 2).
[microP2]: Uses microP2 memory cards (slots 3 and 4).
f Factory setting: [microP2]
Recording is not possible when a card is inserted into a slot that is not selected.
Selects the split method of the recording file.
[ONE FILE]: The clip is recorded in one file in the AVC-LongG format to a microP2 memory card
(exceeding 32 GB).
[SPLIT]: The clip is split every 4 GB regardless of the recording format.
[SHORT SPLIT]: The clip is split every 128 seconds regardless of the recording format.
f Factory setting: [SPLIT]
If the clip is recorded in one file, it cannot be copied to a P2 memory card or 32 GB microP2 memory card,
or copied or exported to storage.
When [ONE FILE] is selected, proxy recording is not possible. Also, when the main menu → [REC/PB]
→ [DUAL CODEC SETUP] → [CODEC USAGE] is set to [PROXY REC(P2)] or [PROXY REC(P2&SD)],
[ONE FILE] cannot be selected.
It will be divided to recording files of approximately 128 seconds when [SHORT SPLIT] is selected, but
they can be operated as a single clip when the thumbnail of the clips are operated on the P2 device. A
single continuous recording time is approximately 3.5 hours.
[SHORT SPLIT] is disabled during the interval recording, the one-shot recording, and the loop recording.
Selects the function that automatically adds a text memo at recording start position each time recording is
started.
[ON]: A text memo is added to each recording.
[OFF]: Does not add a text memo.
f Factory setting: [OFF]
Text memos added when this item is [ON] indicate the recording start position. To record text memos as
character information, refer to "Setting clip metadata" (page 137).
This item is disabled when the main menu → [REC/PB] → [REC FUNCTION] → [RECORDING] is set to
an item other than [NORMAL].
Selects the slot order targeted for recording when power is turned on.
[HOLD]: Records from the recording slot used the last time power was turned off.
[SLOT 1/3]: Each time the power is turned on, this changes in order from slot 1 or 3 (slot selected in [REC
MEDIA]) to the recording target card.
f Factory setting: [HOLD]
Selects acceptance of the start of recording.
[ALL]: Accepts start of recording during stop, during recording pause, and during playback.
[NORMAL]: Accepts start of recording during stop and during recording pause.
f Factory setting: [NORMAL]
If the main menu → [REC/PB] → [REC FUNCTION] → [RECORDING] is set to an item other than
[NORMAL], operation will be [NORMAL] even when this item is set to [ALL].
Selects the method to display recording status at the camera.
[RED]: The red tally lamp illuminates.
[GREEN]: The green tally lamp illuminates.
[CHAR]: The characters "REC" are displayed in the viewfinder.
f Factory setting: [RED]
If set [GREEN] or [CHAR], the viewfinder front tally lamp, back tally lamp and rear tally lamp do not light
while this camera is recording.
Selects whether to light the access LED of the P2 card.
[ON]: Lights.
[OFF]: Does not light.
f Factory setting: [ON]
Selects the position to move when the <FF/REW> button is pressed while playback is paused.
[CLIP]: Top of the clip
[CLIP&TEXT MEMO]: Top of the clip and text memo location
f Factory setting: [CLIP]
– 179 –
Description of settings
Advertisement
Table of Contents
